RichardJones's ROTJ Animefan Paint/Build
- Thread starter RichardJones
- Start date
RichardJones
Active Hunter
Thanks guys! This is my first paint up with an airbrush, and I have to say I am never going back to rattlecans! This time around I'm taking my time studying the gallery reference photos. Is it bad that when I close my eyes I can still see the dome,
I have a few areas to topically fix ( silver around the Killstripes are just a bit off and the turn signals need to be be painted in. ) and then it's on the the lowe/upper cheeks...
RichardJones
Active Hunter
Silver on cheeks masked and humbrol 67 has been misted...
RichardJones
Active Hunter
Thanks, I can't wait either.
This is the third ROTJ paintup I have done, but this time I am going slow and using a more calculated approach!
RichardJones
Active Hunter
I'm getting closer. Tonight I'm going to mask the dark gray on the mandibles and spray some caboose! Then I plan to detail everything out. Some of the silver areas are too thick, so I plan to use some dome green topically to make those areas more appealing/accurate.
RichardJones
Active Hunter
Floquil caboose Red has been added, masking peeled, and now ready for some weathering before sealing with a nice Humbrol satin cote. The red looks really bright here, but it is actually a shade darker and i'm hoping weathering will tone it down even further. Side note, the caboose finished beautifully, but I had to disassemble/clean my airbrush three times during the first and second cote. This is some nasty and difficult paint!
RichardJones
Active Hunter
Thank you TK675.
I'm using an Iwata airbrush, a lower end model but overall it has impressed me with every paint, except the Floquil caboose (which I think may be due its' fast trying time. )
I use a compressor, it's a small tank less setup that I try not to run for too long each session but so far I've been impressed with it. Iwata airbrush/compressor combo, it was a package deal off Amazon.
Last edited by a moderator:
RichardJones
Active Hunter
Yeah they do run out really fast. What i have been doing is mixing enough paint in some clear plastic containers. Be careful though, these containers do NOT like enamel paints, which almost make the containers look like they have been "sandblasted". I am going to find another brand of containers for my ESB paint-up, but you get the idea.
RichardJones
Active Hunter
Well the bright red color makes sense now. I have used some brown pastels to tone the color down a bit. Even my wife said, " is it going to be THAT red?"
facepalmIf i cannot get the color to an acceptable shade, I will re-mask and re-paint with the proper color!
Thanks Jayvee for catching this!
Jayvee
Active Hunter
Well the bright red color makes sense now. I have used some brown pastels to tone the color down a bit. Even my wife said, " is it going to be THAT red?"
If i cannot get the color where to an acceptable shade, I will re-mask and re-paint with the proper color!
Thanks Jayvee for catching this!
Most welcome mate, it's pretty easy to get the two confused...
RichardJones
Active Hunter
I think the weathering toned the red down a good amount..
I'm also adding sintra in the turn signals so they aren't so deep..
intwenothor
Well-Known Hunter
Humbrol 100 might do the trick if you can't find caboose. It was mentioned in an old thread IIRC.
RichardJones
Active Hunter
Thanks Andy, I found the correct bottle of caboose on ebay. It does look alot darker/brown in person, but I do still plan to re paint. In the meantime, I will be working on the ears and possibly re painting the upper cheek area..
intwenothor
Well-Known Hunter
What colour is the upper cheek area? I don't know this helmet very well at all.
RichardJones
Active Hunter
I used Jayvee's paint list for the whole helmet. The upper cheeks are Tamiya XF17,misted with MM Schwartzgrun RLM 70. Both acrylic. I think I misted too much Schwartzgrun, which lightens the overall color. It should be an easy fix.
Similar threads
Want to Buy
ESB flightsuit / vendor(s)?
