MY MSH2.. It has Begun.

dont rush it... (stops to think...) no... rush it... infact I challenge you to finish all the painting in one day. Dont even let the coats dry inbetween. :lol: :lol: :lol:

:moon



*JK*

It will look great... cant wait!
 
The prep work looks fantastic Spidey!! I always wished I put the left cheek scratches in mine....I may have to go back in and add them.

I can't remember the last person to do a full AoSW helmet including the blue marker....should be a nice touch:thumbsup: .......motorfish over at RPF rings a bell, but I can't be sure.

Look forward to the paint progress.

Steve :thumbsup:
 
Wow Spidey!!

I never get over hear much, but I need to start cuz there's so much to learn. I really like what you did to attach the visor. I've always been unsure when I drilled holes in the two helmets I've done, plus the backfilling takes a lot of work. I'm definitely going to use your procedure for my next helmet.

Thanks bro for sharing,
Cruzer
 
Cruzer said:
Wow Spidey!!

I never get over hear much, but I need to start cuz there's so much to learn. I really like what you did to attach the visor. I've always been unsure when I drilled holes in the two helmets I've done, plus the backfilling takes a lot of work. I'm definitely going to use your procedure for my next helmet.

Thanks bro for sharing,
Cruzer
Click to expand...

Thanks Cruzer...:thumbsup: ...and everyone for your comments.

Sorry I haven't been posting on this.....I still have not found a good Method to install a removable headliner...???:wacko ....
Any Idea's???
 
I have to say, that visor installation method is ingenious. Alex, good call on that one. I look forward to this thread !!
 
I have a great idea for that... but I would have to show you what I was thinking.... and see if it would work. It involves a magnet keylock system. :)
 
Per Request...
Here is the way I installed the removable MQ-1 circuit board...

Used the same method on this as the Visor ....using a TEE NUT...as shown in POST #27

hope this helps..;)

MSHv1.jpg


MSHv2.jpg


MSHv2a.jpg


MSHv2b.jpg
 
Spidey... I most say I love when people get detailed about the construction. This is just too ubber good!!! Thank for taking the time to post!!
 
Spidey, I have a question....are you going to deck out the interior with one of Marrow Sun's kits??

As much as I love the exterior of my bucket the interior is just as cool, and is a real eye opener for guests ........

Steve :thumbsup:
 
DL44 Blaster said:
Spidey, I have a question....are you going to deck out the interior with one of Marrow Sun's kits??

As much as I love the exterior of my bucket the interior is just as cool, and is a real eye opener for guests ........

Steve :thumbsup:
Click to expand...

Good call...and already in the works...;)
 
This thread is more than 17 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

Bobamannen
My ESB Boba Fett helmet
Replies
8
Views
1,246
Bobamannen
Bobamannen
Wicked Fett
ROTJ helmet errors on my first real attempt.
Replies
6
Views
804
Wicked Fett
Wicked Fett
Wicked Fett
My attemp at an ROTJ bucket
Replies
2
Views
1,015
Wicked Fett
Wicked Fett
Slave1Pirate117
Need Help Comparing my Helmet
Replies
14
Views
1,624
Slave1Pirate117
Slave1Pirate117
ninjawheel
Airbrushing my first Boba Fett helmet
Replies
2
Views
1,287
AlphaCloneFett
AlphaCloneFett
Back
Top