Boba Fetts Jetpack 3D printed build

Thanks for the info. Rafalfett has a bunch of great stuff listed and at good prices. But, now I can't wait to get printing.


Sent from my iPhone
 
BobasDent1138 said:
A delta printer?? What is that?? Amazing work so far , looks great!! Wish my rocket had fins... lol

Sent from my SAMSUNG-SM-N910A
Click to expand...

A Delta is a printer that's made to do taller prints, so basically I could cut this jetpack into three tall pieces, or just one if the printer was tall enough. The delta I'm working on building can print entire suits of armor. I got a MK5 suit I'm dying to print
 
Here's an update for my jetpack. Almost got the main pack done :)

1bb5cc2000827f453c03b98e439b71ca.jpg
c6ff9601fde4e079c4459e59cd76ce4c.jpg



Sent from my iPad
 

Attachments

  • 1bb5cc2000827f453c03b98e439b71ca.jpg
    1bb5cc2000827f453c03b98e439b71ca.jpg
    356.1 KB · Views: 218
  • c6ff9601fde4e079c4459e59cd76ce4c.jpg
    c6ff9601fde4e079c4459e59cd76ce4c.jpg
    54.5 KB · Views: 245
BobasDent1138 said:
Is there a way you could share the stls? I've been slicing and dicing at these models but no matter how clean I get them the don't quite work...it'd be a great help, but if not , carry on and share progress! :)
-Gav

Sent from my SAMSUNG-SM-N910A
Click to expand...

I'm finishing up the models, and will post them here soon


Sent from my iPad
 
RafalFett said:
That jetpack looks more than great! Did you have problems inserting the tank caps or other main parts?
Click to expand...

The only one I had trouble with, was the lower tank caps...they were a super tight fit. Everything else was just the quirks of splitting files and fitting them together. I'm lucky with the glue I used...bonded the parts within 10 seconds solid...allows me to work with corners and such while it hardens.


Sent from my iPad
 
Last edited by a moderator:
As promised, here's the files that I split. They're cut to fit on a 230X150X140 bed. If you need them smaller, just download the jetpack and load it into Netfabb like I did, and slice away. I believe these should all be cleaned up, but you'll have to orient them how you want. Like I said before, there's a couple of parts that use a lot of support...apologies, but I couldn't do it any other way. I've also included a pic for each file showing where it goes. If you have any problem with the files, let me know.
https://drive.google.com/file/d/0B9KWC9Fh6ZOwNXJQZWozaEJtTlU/view?usp=sharing
 
Drax said:
How much is this going to weigh?
Click to expand...

Mine is about 6 lbs. You could probably drop it down to 4 if you did ABS, two walls, and 5% infill. I used PLA, with four walls, and 20% infill...because PLA is considerably more brittle, but you don't have the warp /shrink factor.


Sent from my iPad
 
This thread is more than 2 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

Bobamannen
Bobamannen's ROTJ build
Replies
9
Views
319
BudaFett
BudaFett
jangobobango
Budget Boba build Aliexpress base
Replies
12
Views
522
jangobobango
jangobobango
Brail khan
boba fett jetpack stl help
Replies
3
Views
219
Brail khan
Brail khan
C
Boba Fett Costume Build
Replies
4
Views
540
SPY007
SPY007
bobawife
Connecting 3D printed pieces?
Replies
1
Views
589
Neo Fett
Neo Fett
Back
Top