Resin parts and tacky paint

B

Buckeye 01

Active Hunter
Hey gang,

I have a slight problem with my blaster. On the backside of my stock bracket (non-grip side) the paint will not dry. It remained tacky for over a month with my last paint job. I had more work to do to it, so I sanded it down to bare resin, and washed with warm water and dish soap. I thought this would cure the problem. I also thought it may have been some crappy paint, so I went to a different store and bought a fresh can of krylon primer, and flat black. About a week ago I applied 3 heavy coats of primer on the entire blaster and I allowed it to dry for almost 5 days. The primer was still a bit tacky when I shot the flat black. I put 4 coats on it, and the handle is once again tacky! It has sat for 2 days now, but the paint refuses to dry! I haven't applied my satin finish yet, nor have I weathered it. I am hoping it will dry once it is weathered and sealed. I doubt it will, but its all I have right now. I posted my progress in the blaster forum and Ripcode thought it may be a poor resin mix that is preventing the paint from fully curing. This is the only spot on my blaster that won't dry, and obviously it's the area that will be handled the most. I don't mind my gloves getting paint on them, but it's one of those things that is buggin the be-jesus out of me. If anyone has any suggestios for me, by all means let me know.
 
Buckeye_01 said:
Hey gang,

I have a slight problem with my blaster. On the backside of my stock bracket (non-grip side) the paint will not dry. It remained tacky for over a month with my last paint job. I had more work to do to it, so I sanded it down to bare resin, and washed with warm water and dish soap. I thought this would cure the problem. I also thought it may have been some crappy paint, so I went to a different store and bought a fresh can of krylon primer, and flat black. About a week ago I applied 3 heavy coats of primer on the entire blaster and I allowed it to dry for almost 5 days. The primer was still a bit tacky when I shot the flat black. I put 4 coats on it, and the handle is once again tacky! It has sat for 2 days now, but the paint refuses to dry! I haven't applied my satin finish yet, nor have I weathered it. I am hoping it will dry once it is weathered and sealed. I doubt it will, but its all I have right now. I posted my progress in the blaster forum and Ripcode thought it may be a poor resin mix that is preventing the paint from fully curing. This is the only spot on my blaster that won't dry, and obviously it's the area that will be handled the most. I don't mind my gloves getting paint on them, but it's one of those things that is buggin the be-jesus out of me. If anyone has any suggestios for me, by all means let me know.
Click to expand...


Does the first and second "Primer Coat" dry completely? If they do, then it is very possible you are applying too many coats of primer AND base, or that each coat is too heavy, and you're not giving the paint room enough to "Gas Out", or not waiting enough time in between coats.

If this is not the case, you may have an area on rifle that continues to sweat. Urethane Resin can "Sweat" after it is cured, especially if it was older resin/contaminated before it was poured. You may have to take the bottom of the stalk and soak it in mineral spirits or acetone for a while before you try and paint it again. After stripping it again of course ;)

If all else fails, you may have to go to the extent of "grinding" that area out, and replace it with body filler, and repeat the paint process. This is an extreme case of course, but I've had to do it from time to time myself. You're essentailly removing the "cancer", so to speak.


Hope this helps ..


FP
 
FP,

Thanks for the response bro. I did let the primer and paint dry about 45 minutes to an hour between every coat. I am beginning to think the resin has/had something wrong with it. On the flip side of that, the back side of the bracket has dried fully. I have been considering having someone cut me one here at work (out of alum), but haven't ponied up and asked yet. This may be the straw that breaks the camels back, BUT the blaster was fully assembled when I bought it. I may be getting more than i'm asking for if I start trying to 'break' this dude apart. Once again, thanks FP, you have been very imformative.
 
It would be free, but having him chuck it up in our CNC machine and draw it up may take some time. I may have to buy him lunch one day and butter him up a bit ;)
 
Buckeye_01 said:
It would be free, but having him chuck it up in our CNC machine and draw it up may take some time. I may have to buy him lunch one day and butter him up a bit ;)
Click to expand...

Well heck if that is the case, I'd get the aluminum one! :lol:
 
I had a weep on a resin part once, cleaned it with meths and then used Tamiya acrylics, brushed on. No stickyness after that.

SAS

Ripcode said:
Well heck if that is the case, I'd get the aluminum one! :lol:
Click to expand...
 
This thread is more than 18 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top