Reply to thread

Message

Not bad! I really don't think your dents are are physically that big, its just that your weathering, (ie your yellow & silver areas) is a bit large. You can make your dents appear much smaller simply by allowing less silver to show through next time. Take for example the ESB VS ROTJ armour. Alot of folks used to say that ESB only had one bullet dent on the left chest plate. We now are almost positive that the armour is the same between the 2. THe only reason you do't really recognize there as being the 2 bullet dents on esb, is simply because one of them is barely weathered. What are you using for masking your weathering?? I would recomend a repaint & perhaps using liquid mask so you get good control of your masking areas. At least I'd try that before scrapping it & making all new armour. Just my 2 cents
Damian

<blockquote data-quote="Jangos kid" data-source="post: 55625" data-attributes="member: 204">Not bad!&nbsp; <img src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f609.png" class="smilie smilie--emoji" loading="lazy" width="64" height="64" alt=";)" title="Wink&nbsp; &nbsp; ;)"&nbsp; data-smilie="2"data-shortname=";)" />&nbsp; I really don&#039;t think your dents are are physically that big, its just that your weathering, (ie your yellow &amp; silver areas) is a bit large.&nbsp; You can make your dents appear much smaller simply by allowing less silver to show through next time. Take for example the ESB VS ROTJ armour.&nbsp; Alot of folks used to say that ESB only had one bullet dent on the left chest plate.&nbsp; We now are almost positive that the armour is the same between the 2.&nbsp; THe only reason you do&#039;t really recognize there as being the 2 bullet dents on esb, is simply because one of them is barely weathered. What are you using for masking your weathering??&nbsp; I would recomend a repaint &amp; perhaps using liquid mask so you get good control of your masking areas.&nbsp; At least I&#039;d try that before scrapping it &amp; making all new armour.&nbsp; Just my 2 cents<img src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f609.png" class="smilie smilie--emoji" loading="lazy" width="64" height="64" alt=";)" title="Wink&nbsp; &nbsp; ;)"&nbsp; data-smilie="2"data-shortname=";)" />Damian</blockquote>

[QUOTE="Jangos kid, post: 55625, member: 204"] Not bad! ;) I really don't think your dents are are physically that big, its just that your weathering, (ie your yellow & silver areas) is a bit large. You can make your dents appear much smaller simply by allowing less silver to show through next time. Take for example the ESB VS ROTJ armour. Alot of folks used to say that ESB only had one bullet dent on the left chest plate. We now are almost positive that the armour is the same between the 2. THe only reason you do't really recognize there as being the 2 bullet dents on esb, is simply because one of them is barely weathered. What are you using for masking your weathering?? I would recomend a repaint & perhaps using liquid mask so you get good control of your masking areas. At least I'd try that before scrapping it & making all new armour. Just my 2 cents;) Damian [/QUOTE]

This thread is more than 19 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification