Reply to thread

Message

I have now finished modifying my jet pack to match the AOSW version. A big thanks to Brak's for the pics he posted a short while ago, these really helped with the detailing. Here's what I've done:

PIC 1: I have deepened the recess on the underside then fitted, painted and weathered the three buttons/plugs.

PIC 2: The plug and small switch are added to the underside.

PIC 3: Aluminium hooks are made and screwed to the body and a smaller door is built that has four locking screws.

PIC 4: The small mole is sculpted and added.

PIC 5: The rocket is altered to match the screen used one.

I still need to make two more aluminium hooks that will be attached to the bottom of the pack, these hold the scuba belt in position, these can be seen on the screen used shots from Brak's.

DAZ

[ATTACH=full]7602[/ATTACH]

[ATTACH=full]7603[/ATTACH]

[ATTACH=full]7604[/ATTACH]

[ATTACH=full]7605[/ATTACH]

[ATTACH=full]7606[/ATTACH]

<blockquote data-quote="bobamaker" data-source="post: 113477" data-attributes="member: 450">I have now finished modifying my jet pack to match the AOSW version. A big thanks to Brak&#039;s for the pics he posted a short while ago, these really helped with the detailing. Here&#039;s what I&#039;ve done:&nbsp;PIC 1: I have deepened the recess on the underside then fitted, painted and weathered the three buttons/plugs.&nbsp;PIC 2: The plug and small switch are added to the underside.&nbsp;PIC 3: Aluminium hooks are made and screwed to the body and a smaller door is built that has four locking screws.&nbsp;PIC 4: The small mole is sculpted and added.&nbsp;PIC 5: The rocket is altered to match the screen used one.&nbsp;I still need to make two more aluminium hooks that will be attached to the bottom of the pack, these hold the scuba belt in position, these can be seen on the screen used shots from Brak&#039;s.&nbsp;DAZ[ATTACH=full]7602[/ATTACH][ATTACH=full]7603[/ATTACH][ATTACH=full]7604[/ATTACH][ATTACH=full]7605[/ATTACH][ATTACH=full]7606[/ATTACH]</blockquote>

[QUOTE="bobamaker, post: 113477, member: 450"] I have now finished modifying my jet pack to match the AOSW version. A big thanks to Brak's for the pics he posted a short while ago, these really helped with the detailing. Here's what I've done: PIC 1: I have deepened the recess on the underside then fitted, painted and weathered the three buttons/plugs. PIC 2: The plug and small switch are added to the underside. PIC 3: Aluminium hooks are made and screwed to the body and a smaller door is built that has four locking screws. PIC 4: The small mole is sculpted and added. PIC 5: The rocket is altered to match the screen used one. I still need to make two more aluminium hooks that will be attached to the bottom of the pack, these hold the scuba belt in position, these can be seen on the screen used shots from Brak's. DAZ [ATTACH=full]7602[/ATTACH] [ATTACH=full]7603[/ATTACH] [ATTACH=full]7604[/ATTACH] [ATTACH=full]7605[/ATTACH] [ATTACH=full]7606[/ATTACH] [/QUOTE]

This thread is more than 18 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification