Reply to thread

Message

Heres a couple of pics form the con this weekend....This is my freind Jennifer in her awesome Batgirl...
[ATTACH=full]143035[/ATTACH]
Funny Story...we bumped into each other...not hard at all, and my thruster broke clean off lol. She felt so bad! I told her shes the strongest Batgirl i know! LOL!

I wasnt concerned because i knew i could just make another....the reason it broke was because the set i put on my pack was the lightest set i could make, and i had a feeling they wouldnt be too strong, didnt think they would break THAT easily though lol. This set was completely foam filled and the resin layer was fairly thin. I usually make the attachment post area soild resin when i cast these, to avapid breakage..but i did this set to see how far i could go with weight strength ratio.. apparently i went too far LOL. But i already cast a replacemnt one and will have it ready for next time.

[ATTACH=full]143036[/ATTACH]

My sister-in-law Melyssa, myself and the wife
[ATTACH=full]143037[/ATTACH]

Here is proof my jetpack isnt huge...well the best shot i could find lol
[ATTACH=full]143038[/ATTACH]

<blockquote data-quote="Darth Voorhees" data-source="post: 419449" data-attributes="member: 2367">Heres a couple of pics form the con this weekend....This is my freind Jennifer in her awesome Batgirl...[ATTACH=full]143035[/ATTACH]Funny Story...we bumped into each other...not hard at all, and my thruster broke clean off lol. She felt so bad! I told her shes the strongest Batgirl i know! LOL!I wasnt concerned because i knew i could just make another....the reason it broke was because the set i put on my pack was the lightest set i could make, and i had a feeling they wouldnt be too strong, didnt think they would break THAT easily though lol. This set was completely foam filled and the resin layer was fairly thin. I usually make the attachment post area soild resin when i cast these, to avapid breakage..but i did this set to see how far i could go with weight strength ratio.. apparently i went too far LOL. But i already cast a replacemnt one and will have it ready for next time.[ATTACH=full]143036[/ATTACH]My sister-in-law Melyssa, myself and the wife[ATTACH=full]143037[/ATTACH]Here is proof my jetpack isnt huge...well the best shot i could find lol[ATTACH=full]143038[/ATTACH]</blockquote>

[QUOTE="Darth Voorhees, post: 419449, member: 2367"] Heres a couple of pics form the con this weekend....This is my freind Jennifer in her awesome Batgirl... [ATTACH=full]143035[/ATTACH] Funny Story...we bumped into each other...not hard at all, and my thruster broke clean off lol. She felt so bad! I told her shes the strongest Batgirl i know! LOL! I wasnt concerned because i knew i could just make another....the reason it broke was because the set i put on my pack was the lightest set i could make, and i had a feeling they wouldnt be too strong, didnt think they would break THAT easily though lol. This set was completely foam filled and the resin layer was fairly thin. I usually make the attachment post area soild resin when i cast these, to avapid breakage..but i did this set to see how far i could go with weight strength ratio.. apparently i went too far LOL. But i already cast a replacemnt one and will have it ready for next time. [ATTACH=full]143036[/ATTACH] My sister-in-law Melyssa, myself and the wife [ATTACH=full]143037[/ATTACH] Here is proof my jetpack isnt huge...well the best shot i could find lol [ATTACH=full]143038[/ATTACH] [/QUOTE]

This thread is more than 9 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification