Reply to thread

Message

Re:**UPDATE** CONVERTING BKBT's JANGO BUCKET TO BOBA *PICS*

Well, I've finally finished the modifications to my BKBT bucket. All that's left to do is cut out the visor area and start painting. I've already started painting the ears. The remaining things I had to do was:

1) Reduce the width of the horizontal part of the visor (from ear to ear, not top to bottom).

2) Increase the length of the areas behind the ears and change their angle slightly. Based on reference photos they don't angle the same on both sides.

3) Alter the keyslot area.

(The areas highlighted in blue are the areas that had to be filled or have their shape altered. The Pics actually loaded backwards!? The finished product pic preceeds the pic showing where the augmentation was made.)

[ATTACH=full]1431[/ATTACH]

[ATTACH=full]1432[/ATTACH]

[ATTACH=full]1433[/ATTACH]

[ATTACH=full]1434[/ATTACH]

[ATTACH=full]1435[/ATTACH]

[ATTACH=full]1436[/ATTACH]

[ATTACH=full]1437[/ATTACH]

[ATTACH=full]1438[/ATTACH]

[ATTACH=full]1439[/ATTACH]

<blockquote data-quote="AFettFullofDollars" data-source="post: 48473" data-attributes="member: 419">Re:**UPDATE** CONVERTING BKBT&#039;s JANGO BUCKET TO BOBA *PICS*Well, I&#039;ve finally finished the modifications to my BKBT bucket. All that&#039;s left to do is cut out the visor area and start painting. I&#039;ve already started painting the ears. The remaining things I had to do was:&nbsp;1) Reduce the width of the horizontal part of the visor (from ear to ear, not top to bottom).&nbsp;2) Increase the length of the areas behind the ears and change their angle slightly. Based on reference photos they don&#039;t angle the same on both sides.&nbsp;3) Alter the keyslot area.&nbsp;(The areas highlighted in blue are the areas that had to be filled or have their shape altered. The Pics actually loaded backwards!? The finished product pic preceeds the pic showing where the augmentation was made.)[ATTACH=full]1431[/ATTACH][ATTACH=full]1432[/ATTACH][ATTACH=full]1433[/ATTACH][ATTACH=full]1434[/ATTACH][ATTACH=full]1435[/ATTACH][ATTACH=full]1436[/ATTACH][ATTACH=full]1437[/ATTACH][ATTACH=full]1438[/ATTACH][ATTACH=full]1439[/ATTACH]</blockquote>

[QUOTE="AFettFullofDollars, post: 48473, member: 419"] [b]Re:**UPDATE** CONVERTING BKBT's JANGO BUCKET TO BOBA *PICS*[/b] Well, I've finally finished the modifications to my BKBT bucket. All that's left to do is cut out the visor area and start painting. I've already started painting the ears. The remaining things I had to do was: 1) Reduce the width of the horizontal part of the visor (from ear to ear, not top to bottom). 2) Increase the length of the areas behind the ears and change their angle slightly. Based on reference photos they don't angle the same on both sides. 3) Alter the keyslot area. (The areas highlighted in blue are the areas that had to be filled or have their shape altered. The Pics actually loaded backwards!? The finished product pic preceeds the pic showing where the augmentation was made.) [ATTACH=full]1431[/ATTACH] [ATTACH=full]1432[/ATTACH] [ATTACH=full]1433[/ATTACH] [ATTACH=full]1434[/ATTACH] [ATTACH=full]1435[/ATTACH] [ATTACH=full]1436[/ATTACH] [ATTACH=full]1437[/ATTACH] [ATTACH=full]1438[/ATTACH] [ATTACH=full]1439[/ATTACH] [/QUOTE]

This thread is more than 17 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification