Reply to thread

Message

Greetings all,

I've recently started on making a new ROTJ SE suit and wanted to share my progress with you all.

I realized I had shared some parts elsewhere but not here on TDH where I first began my Fett journey all those years ago so I'm making sure to chronicle the journey here as well.

Helmet - MinuteFett lineage cast
Helmet Mq-1 board - Neo Prop Shop replica (Resin cast of the MQ-1 Circuit board)
Visor - Tvisor
Armor - MinuteFett lineage
Armor studs - Neo Prop Shop replica (Resin cast of Royal 242PD keyboard keys)
Chestplate display - Westaby Electronics
Ammo belt - Handmade Horror Shop
Boots- MOWS
Boot toe spikes - MasterCraft Replicas
Jetpack - Bobamaker
Jetpack Thrusters - MasterCraft Replicas
Thruster Greeblies - MasterCraft Replicas
Jetpack harness - Fett 4 Real
Gauntlets - MinuteFett
Gauntlet darts - MasterCraft Replicas
Gauntlet Alco switches - Alco MPA 106D
Mq1 keypad replica - Neo Prop Shop
Girth belt - ReGeeked Props
Flakvest - CB Props
Jumpsuit w/neckseal - CB Props
Wookie braids - Made by me
Gloves - unknown maker

Here is my old inaccurate Fett armor from 15 years ago that I planned to refurbish, but now I'm in the process of just replacing most of it with accurate pieces...

[ATTACH=full]243709[/ATTACH]
[ATTACH=full]243710[/ATTACH]

Then there is the new vac-formed armor from MinuteFett...

[ATTACH=full]243711[/ATTACH]

So, after hours of trimming, sanding, and prepping, I applied the first layer of primer/filler.

[ATTACH=full]243712[/ATTACH]
[ATTACH=full]243713[/ATTACH]

And here is my first attempt at 3D printing: the EE-3 carbine that I assembled, painted, and displayed until I have a finished kit.

[ATTACH=full]243714[/ATTACH]
[ATTACH=full]243715[/ATTACH]

I was able to get all the pieces covered with the metallic silver base and then the damaged areas masked with masking fluid.

[ATTACH=full]243716[/ATTACH]
[ATTACH=full]243717[/ATTACH]

Next up was getting each piece painted with the base color.

[ATTACH=full]243718[/ATTACH]
[ATTACH=full]243719[/ATTACH]

Once they were all dry, I began the tedious yet satisfying process of pulling all the masking fluid off to reveal the silver underneath.

[ATTACH=full]243720[/ATTACH]
[ATTACH=full]243721[/ATTACH]

<blockquote data-quote="AdenSolu" data-source="post: 535455" data-attributes="member: 4626">Greetings all,I&#039;ve recently started on making a new ROTJ SE suit and wanted to share my progress with you all.I realized I had shared some parts elsewhere but not here on TDH where I first began my Fett journey all those years ago so I&#039;m making sure to chronicle the journey here as well.Helmet - MinuteFett lineage castHelmet Mq-1 board - Neo Prop Shop replica (Resin cast of the MQ-1 Circuit board)Visor - TvisorArmor - MinuteFett lineageArmor studs - Neo Prop Shop replica (Resin cast of Royal 242PD keyboard keys)Chestplate display - Westaby ElectronicsAmmo belt - Handmade Horror Shop Boots- MOWSBoot toe spikes - MasterCraft ReplicasJetpack - BobamakerJetpack Thrusters - MasterCraft ReplicasThruster Greeblies - MasterCraft ReplicasJetpack harness - Fett 4 RealGauntlets - MinuteFettGauntlet darts - MasterCraft ReplicasGauntlet Alco switches - Alco MPA 106DMq1 keypad replica - Neo Prop ShopGirth belt - ReGeeked PropsFlakvest - CB PropsJumpsuit w/neckseal - CB PropsWookie braids - Made by meGloves - unknown makerHere is my old inaccurate Fett armor from 15 years ago that I planned to refurbish, but now I&#039;m in the process of just replacing most of it with accurate pieces...[ATTACH=full]243709[/ATTACH][ATTACH=full]243710[/ATTACH]Then there is the new vac-formed armor from MinuteFett...[ATTACH=full]243711[/ATTACH]So, after hours of trimming, sanding, and prepping, I applied the first layer of primer/filler.[ATTACH=full]243712[/ATTACH][ATTACH=full]243713[/ATTACH]And here is my first attempt at 3D printing: the EE-3 carbine that I assembled, painted, and displayed until I have a finished kit.[ATTACH=full]243714[/ATTACH][ATTACH=full]243715[/ATTACH]I was able to get all the pieces covered with the metallic silver base and then the damaged areas masked with masking fluid.[ATTACH=full]243716[/ATTACH][ATTACH=full]243717[/ATTACH]Next up was getting each piece painted with the base color.[ATTACH=full]243718[/ATTACH][ATTACH=full]243719[/ATTACH]Once they were all dry, I began the tedious yet satisfying process of pulling all the masking fluid off to reveal the silver underneath.[ATTACH=full]243720[/ATTACH][ATTACH=full]243721[/ATTACH]</blockquote>

[QUOTE="AdenSolu, post: 535455, member: 4626"] Greetings all, I've recently started on making a new ROTJ SE suit and wanted to share my progress with you all. I realized I had shared some parts elsewhere but not here on TDH where I first began my Fett journey all those years ago so I'm making sure to chronicle the journey here as well. Helmet - MinuteFett lineage cast Helmet Mq-1 board - Neo Prop Shop replica (Resin cast of the MQ-1 Circuit board) Visor - Tvisor Armor - MinuteFett lineage Armor studs - Neo Prop Shop replica (Resin cast of Royal 242PD keyboard keys) Chestplate display - Westaby Electronics Ammo belt - Handmade Horror Shop Boots- MOWS Boot toe spikes - MasterCraft Replicas Jetpack - Bobamaker Jetpack Thrusters - MasterCraft Replicas Thruster Greeblies - MasterCraft Replicas Jetpack harness - Fett 4 Real Gauntlets - MinuteFett Gauntlet darts - MasterCraft Replicas Gauntlet Alco switches - Alco MPA 106D Mq1 keypad replica - Neo Prop Shop Girth belt - ReGeeked Props Flakvest - CB Props Jumpsuit w/neckseal - CB Props Wookie braids - Made by me Gloves - unknown maker Here is my old inaccurate Fett armor from 15 years ago that I planned to refurbish, but now I'm in the process of just replacing most of it with accurate pieces... [ATTACH type="full" alt="v3ghrSl.jpg"]243709[/ATTACH] [ATTACH type="full" alt="JUORu1n.jpg"]243710[/ATTACH] Then there is the new vac-formed armor from MinuteFett... [ATTACH type="full" alt="coMX81R.jpg"]243711[/ATTACH] So, after hours of trimming, sanding, and prepping, I applied the first layer of primer/filler. [ATTACH type="full" alt="YjTolBH.jpg"]243712[/ATTACH] [ATTACH type="full" alt="FBdIiDi.jpg"]243713[/ATTACH] And here is my first attempt at 3D printing: the EE-3 carbine that I assembled, painted, and displayed until I have a finished kit. [ATTACH type="full" alt="jQqcmN1.jpg"]243714[/ATTACH] [ATTACH type="full" alt="wUJQQXe.jpg"]243715[/ATTACH] I was able to get all the pieces covered with the metallic silver base and then the damaged areas masked with masking fluid. [ATTACH type="full" alt="ZbfBJsb.jpg"]243716[/ATTACH] [ATTACH type="full" alt="vXnwglq.jpg"]243717[/ATTACH] Next up was getting each piece painted with the base color. [ATTACH type="full" alt="jzcXwB6.jpg"]243718[/ATTACH] [ATTACH type="full" alt="xTyAKzU.jpg"]243719[/ATTACH] Once they were all dry, I began the tedious yet satisfying process of pulling all the masking fluid off to reveal the silver underneath. [ATTACH type="full" alt="HWUo9LI.jpg"]243720[/ATTACH] [ATTACH type="full" alt="ca2PXFV.jpg"]243721[/ATTACH] [/QUOTE]

This thread is more than 3 months old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification