Reply to thread

Message

Small update.

Shot everything with primer. There will need to be a little sanding done but that was to be expected. Overall, the print by [USER=14255]Lazerjock[/USER] is very smooth. [ATTACH=full]221171[/ATTACH]

There were a few spots that needed to be filled. I did not initially see these due to the translucency of the resin material.
[ATTACH=full]221172[/ATTACH]
[ATTACH=full]221173[/ATTACH]
[ATTACH=full]221174[/ATTACH]

No problem though. I just need to fill the gaps with the same Bondo glazing putty that I used for the BM helmet repair.
[ATTACH=full]221175[/ATTACH]

Now to let the putty dry and then sand it down smooth.
[ATTACH=full]221176[/ATTACH]

I also picked up the replica EE-3 hardware set from [USER=14113]Airmarshal[/USER]. Honestly, it was a little pricey but in this hobby what isn’t? I think they will add a nice touch though.
[ATTACH=full]221177[/ATTACH]

That’s all for now. Slowly chipping away at it. Thanks.

<blockquote data-quote="ShortFuse" data-source="post: 521734" data-attributes="member: 8494">Small update. Shot everything with primer. There will need to be a little sanding done but that was to be expected. Overall, the print by [USER=14255]Lazerjock[/USER] is very smooth. [ATTACH=full]221171[/ATTACH]There were a few spots that needed to be filled. I did not initially see these due to the translucency of the resin material. [ATTACH=full]221172[/ATTACH][ATTACH=full]221173[/ATTACH][ATTACH=full]221174[/ATTACH]No problem though. I just need to fill the gaps with the same Bondo glazing putty that I used for the BM helmet repair. [ATTACH=full]221175[/ATTACH]Now to let the putty dry and then sand it down smooth. [ATTACH=full]221176[/ATTACH]I also picked up the replica EE-3 hardware set from [USER=14113]Airmarshal[/USER]. Honestly, it was a little pricey but in this hobby what isn’t? I think they will add a nice touch though. [ATTACH=full]221177[/ATTACH]That’s all for now. Slowly chipping away at it. Thanks.</blockquote>

[QUOTE="ShortFuse, post: 521734, member: 8494"] Small update. Shot everything with primer. There will need to be a little sanding done but that was to be expected. Overall, the print by [USER=14255]Lazerjock[/USER] is very smooth. [ATTACH type="full"]221171[/ATTACH] There were a few spots that needed to be filled. I did not initially see these due to the translucency of the resin material. [ATTACH type="full"]221172[/ATTACH] [ATTACH type="full"]221173[/ATTACH] [ATTACH type="full"]221174[/ATTACH] No problem though. I just need to fill the gaps with the same Bondo glazing putty that I used for the BM helmet repair. [ATTACH type="full"]221175[/ATTACH] Now to let the putty dry and then sand it down smooth. [ATTACH type="full"]221176[/ATTACH] I also picked up the replica EE-3 hardware set from [USER=14113]Airmarshal[/USER]. Honestly, it was a little pricey but in this hobby what isn’t? I think they will add a nice touch though. [ATTACH type="full"]221177[/ATTACH] That’s all for now. Slowly chipping away at it. Thanks. [/QUOTE]

This thread is more than 2 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification