Reply to thread

Message

While waiting for the filler to dry, I went ahead and prepped the T-visor so that I may temporarily hot glue it into place for the next sections that will be painted, should give the bucket a lot more stability.

[ATTACH=full]142785[/ATTACH]

on a side note, I did a test fit of this visor and wouldn't you know it, it fit almost darn near perfect!! With any luck, the third time will be the charm (trying to get the last two to fit was a total fail!)

- - - Updated - - -

And whoa lah, all done and ready for the next steps.

[ATTACH=full]142786[/ATTACH]
[ATTACH=full]142787[/ATTACH]

- - - Updated - - -

All set and ready for some silver. I decided to try the Testors Diamond Dust and see how it looks. (Another Safety Warning, PLEASE use a paint mask and eye protection when spraying the diamond dust!! Trust me, It gets everywhere!!). I figure if I screw it up, I can always sand it down and then go with the the humbrol 11 and metalcote combo.

[ATTACH=full]142788[/ATTACH]

<blockquote data-quote="tjr2d2" data-source="post: 418003" data-attributes="member: 6803">While waiting for the filler to dry, I went ahead and prepped the T-visor so that I may temporarily hot glue it into place for the next sections that will be painted, should give the bucket a lot more stability.&nbsp; [ATTACH=full]142785[/ATTACH]on a side note, I did a test fit of this visor and wouldn&#039;t you know it, it fit almost darn near perfect!!&nbsp; With any luck, the third time will be the charm (trying to get the last two to fit was a total fail!)- - - Updated - - -And whoa lah, all done and ready for the next steps.&nbsp; [ATTACH=full]142786[/ATTACH][ATTACH=full]142787[/ATTACH]- - - Updated - - -All set and ready for some silver.&nbsp; I decided to try the Testors Diamond Dust and see how it looks. (Another Safety Warning, PLEASE use a paint mask and eye protection when spraying the diamond dust!! Trust me, It gets everywhere!!). I figure if I screw it up, I can always sand it down and then go with the the humbrol 11 and metalcote combo. [ATTACH=full]142788[/ATTACH]</blockquote>

[QUOTE="tjr2d2, post: 418003, member: 6803"] While waiting for the filler to dry, I went ahead and prepped the T-visor so that I may temporarily hot glue it into place for the next sections that will be painted, should give the bucket a lot more stability. [ATTACH=full]142785[/ATTACH] on a side note, I did a test fit of this visor and wouldn't you know it, it fit almost darn near perfect!! With any luck, the third time will be the charm (trying to get the last two to fit was a total fail!) [SIZE=1]- - - Updated - - -[/SIZE] And whoa lah, all done and ready for the next steps. [ATTACH=full]142786[/ATTACH] [ATTACH=full]142787[/ATTACH] [SIZE=1]- - - Updated - - -[/SIZE] All set and ready for some silver. I decided to try the Testors Diamond Dust and see how it looks. (Another Safety Warning, PLEASE use a paint mask and eye protection when spraying the diamond dust!! Trust me, It gets everywhere!!). I figure if I screw it up, I can always sand it down and then go with the the humbrol 11 and metalcote combo. [ATTACH=full]142788[/ATTACH] [/QUOTE]

This thread is more than 3 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification