Reply to thread

Message: <blockquote data-quote="micke" data-source="post: 83175" data-attributes="member: 83">Prepro helmet v.2 FINISHED (see 1st post)It's finally done. Thanks to Rune Spaans for Photographing the helmet!<img src="http://www.noguchi.no/misc/prepro2_finished_01.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_02.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_03.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_04.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_05.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_06.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_07.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_08.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_09.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" /><img src="http://www.noguchi.no/misc/prepro2_finished_10.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" />I hope you have enjoyed the thread and that you like the finished result<img src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f642.png" class="smilie smilie--emoji" loading="lazy" width="64" height="64" alt=":)" title="Smile    :)"  data-smilie="1"data-shortname=":)" />-Mikael---------------------------------------------------------------------------It's been a long time since my last helmet. I have been busy with moving into a new place and other family stuff. It's about time to start something new! This is one of the original MSH1 helmets that i have done some some  modifictations to. I mainly did some changes to the dent and visor area. I rebuildt it a bit because i thought it was a little too open. i also made the dent a little smaller. Still some work left before paint. I will post newer pictures as i progress. There was quite a bit of trimming adn sanding. I've spent close to 30 hours on it til now. It's hard to see, but i used a dremel to make the damage on the surface. It has some smaller chips here and there and some scratches.  What do you think?If anyone has any suggestions or tips i would be glad to hear<img src="https://cdn.jsdelivr.net/joypixels/assets/8.0/png/unicode/64/1f642.png" class="smilie smilie--emoji" loading="lazy" width="64" height="64" alt=":)" title="Smile    :)"  data-smilie="1"data-shortname=":)" /> <img src="http://www.noguchi.no/misc/prepped.jpg" alt="" class="fr-fic fr-dii fr-draggable " data-size="" style="" />My next steps would be: -Get a new RF top.-Install the visor.-Complete all the scratches and chipping.-Cut the borden connector.-Widen the gap on the visor area jus a little.-Make the shape of the dent better.-Sand down the left side of the mandibles as the original is not as symmetric.-Install the circuit board in the rear. I still dont know what these 2 stubbs on the circuitboard is. They are on the rear of the ROTJ helmet as well. Any ideas? -Micke[ATTACH=full]5130[/ATTACH]</blockquote>

This thread is more than 18 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification