Reply to thread

Message

Hi all. Just wanted to share the progress I'm making on my ESB EE-3. It's not finished yet, but it's finally starting to resemble the best ugly blaster from the films.

Parts:
Blaster: Bronze Hand Schaub Webley
Barrel: Heiland 2-cell
Resin bits: Mixture of Stormrider (stock greeblies, Molex connectors) and Sidewinder (barrel mounts, V-8 greeblies, lanyard rings)
Scope: Vintage type-2 Milbro 4x20

I stained the stock and gave a once over to the barrel section. I also painted up the resin bits. I still have to weather everything (combo of dry brush and acrylic washes) and attach the lanyard rings. I also have to finish painting the greeblies on the stock. I am hesitant to put any paint on the scope since it looks so nice, but I think that it needs it.

I can't wait to see how it looks when it's finished. I think I'm going to go the route that RedArc went and install a Plecter Labs blastercore. I just have to build up the courage to cut out the trigger and replace it with a functioning one. Anyhow, enough yapping. Here are a few pics. I'll update when I have done more.

[ATTACH]42843[/ATTACH][ATTACH]42844[/ATTACH][ATTACH]42845[/ATTACH]

<blockquote data-quote="bcurtis" data-source="post: 382778" data-attributes="member: 6755">Hi all. Just wanted to share the progress I&#039;m making on my ESB EE-3. It&#039;s not finished yet, but it&#039;s finally starting to resemble the best ugly blaster from the films. Parts:Blaster: Bronze Hand Schaub WebleyBarrel: Heiland 2-cellResin bits: Mixture of Stormrider (stock greeblies, Molex connectors) and Sidewinder (barrel mounts, V-8 greeblies, lanyard rings)Scope: Vintage type-2 Milbro 4x20I stained the stock and gave a once over to the barrel section. I also painted up the resin bits. I still have to weather everything (combo of dry brush and acrylic washes) and attach the lanyard rings. I also have to finish painting the greeblies on the stock. I am hesitant to put any paint on the scope since it looks so nice, but I think that it needs it. &nbsp;I can&#039;t wait to see how it looks when it&#039;s finished. I think I&#039;m going to go the route that RedArc went and install a Plecter Labs blastercore. I just have to build up the courage to cut out the trigger and replace it with a functioning one. Anyhow, enough yapping. Here are a few pics. I&#039;ll update when I have done more.[ATTACH]42843[/ATTACH][ATTACH]42844[/ATTACH][ATTACH]42845[/ATTACH]</blockquote>

[QUOTE="bcurtis, post: 382778, member: 6755"] Hi all. Just wanted to share the progress I'm making on my ESB EE-3. It's not finished yet, but it's finally starting to resemble the best ugly blaster from the films. Parts: Blaster: Bronze Hand Schaub Webley Barrel: Heiland 2-cell Resin bits: Mixture of Stormrider (stock greeblies, Molex connectors) and Sidewinder (barrel mounts, V-8 greeblies, lanyard rings) Scope: Vintage type-2 Milbro 4x20 I stained the stock and gave a once over to the barrel section. I also painted up the resin bits. I still have to weather everything (combo of dry brush and acrylic washes) and attach the lanyard rings. I also have to finish painting the greeblies on the stock. I am hesitant to put any paint on the scope since it looks so nice, but I think that it needs it. I can't wait to see how it looks when it's finished. I think I'm going to go the route that RedArc went and install a Plecter Labs blastercore. I just have to build up the courage to cut out the trigger and replace it with a functioning one. Anyhow, enough yapping. Here are a few pics. I'll update when I have done more. [ATTACH]42843.vB[/ATTACH][ATTACH]42844.vB[/ATTACH][ATTACH]42845.vB[/ATTACH] [/QUOTE]

This thread is more than 9 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification