Reply to thread

Message

Confined indoors today, as maintenance men were occupying the outside of the building, pressure cleaning the entire apartment, so got some more work done to this...

I began fixing the rear. I'd say the biggest obstacle with this is getting the entire back side of this sculpt clean. You can see the nastiness of it. I'm thinking that I'm going to cover the entire dome and back end in the new clay, as it's much better quality and much easier to work with.

Overlooking the 3d model, it appears that the back is supposed to be rounded, versus the sharp angled look of it before, therefore, I've added more clay to "round" it out. Still needs some minor work and smoothing, but almost there.

[ATTACH=full]82116[/ATTACH]

[ATTACH=full]82117[/ATTACH]

[ATTACH=full]82118[/ATTACH]

Since I was re-working this area, I've decided to try and pronounce the detail, but think I need to round it down and give it a lower profile..

[ATTACH=full]82119[/ATTACH]

[ATTACH=full]82120[/ATTACH]

Getting there...

-TC

<blockquote data-quote="tubachris85x" data-source="post: 103597" data-attributes="member: 1226">Confined indoors today, as maintenance men were occupying the outside of the building, pressure cleaning the entire apartment, so got some more work done to this...I began fixing the rear. I&#039;d say the biggest obstacle with this is getting the entire back side of this sculpt clean. You can see the nastiness of it. I&#039;m thinking that I&#039;m going to cover the entire dome and back end in the new clay, as it&#039;s much better quality and much easier to work with. Overlooking the 3d model, it appears that the back is supposed to be rounded, versus the sharp angled look of it before, therefore, I&#039;ve added more clay to &quot;round&quot; it out. Still needs some minor work and smoothing, but almost there.[ATTACH=full]82116[/ATTACH][ATTACH=full]82117[/ATTACH][ATTACH=full]82118[/ATTACH]Since I was re-working this area, I&#039;ve decided to try and pronounce the detail, but think I need to round it down and give it a lower profile..[ATTACH=full]82119[/ATTACH][ATTACH=full]82120[/ATTACH]Getting there...-TC</blockquote>

[QUOTE="tubachris85x, post: 103597, member: 1226"] Confined indoors today, as maintenance men were occupying the outside of the building, pressure cleaning the entire apartment, so got some more work done to this... I began fixing the rear. I'd say the biggest obstacle with this is getting the entire back side of this sculpt clean. You can see the nastiness of it. I'm thinking that I'm going to cover the entire dome and back end in the new clay, as it's much better quality and much easier to work with. Overlooking the 3d model, it appears that the back is supposed to be rounded, versus the sharp angled look of it before, therefore, I've added more clay to "round" it out. Still needs some minor work and smoothing, but almost there. [ATTACH=full]82116[/ATTACH] [ATTACH=full]82117[/ATTACH] [ATTACH=full]82118[/ATTACH] Since I was re-working this area, I've decided to try and pronounce the detail, but think I need to round it down and give it a lower profile.. [ATTACH=full]82119[/ATTACH] [ATTACH=full]82120[/ATTACH] Getting there... -TC [/QUOTE]

This thread is more than 10 years old.

Your message may be considered spam for the following reasons:

This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.

If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

I am aware that replying to this thread may be considered spam, but I still want to make a reply.

Verification