Reply to thread

OK. Should have done that to start with...


Source

  • Helmet - FPH2 by Fett Pride (bought from Major). Painted by me.
  • Dry Rub helmet markings - SuperJedi. (Highly recommended)
  • Helmet ear decals - Lucksy31
  • Hollow Stalk (for helmet) - Machine Craft. Weathered by me.
  • Rangefinder topper - Shapeways, design by RafalFett
  • Visor - T-visors.com - FP Deluxe
  • Servo kit and Rangefiner lights- SalamanderKing with heavy customization by me. I bought a lo profile servo and wired some Alco switches.
  • Flight Suit - Arkady. Weathered by me.
  • Flak Vest - Arkady. Painted by me.
  • Armor - Collar, chest, centerpiece, shoulders, and abdomen from korbanth, which I had to strip down and repaint. Very solid armor, though. Back plate, cod, kidney armor, and knee armor from RKD. All painted by myself.
  • Collar and Cod studs - Shapeways, desing by ToolGuy. Painted by me.
  • Chest lights - hot pockets
  • Chest decals - Lucksy31
  • Knee Darts - Machine Craft.
  • Gauntlets - RKD. The version with the resin upper and bolatron lower. Painted by Lou @ DVH.
  • Gauntlet darts - RKD
  • Gauntlet light - scratchbuilt using parts from ledsupply.com. I bought the switch off of Amazon.
  • Casio MQ-1 - found part for gauntlet
  • Flamethrower w/ acrylic nozzle - Combat Baby - serial #0001 on the nozzle (thanks for working through several prototypes, CB. It rocks!) painted by Lou @ DVH
  • Jet Pack - DVH. Painted by DVH.
  • Jet Pack harness - Big Dane with soft parts sewn and riveted by me.
  • Scuba buckle - Dacor (same era as US Divers, different stamp).
  • Beacon - Machine Craft. Finished by me.
  • Beacon light - JC27 (Fettinator Industries)
  • Aluminum Stabilizer - beats me
  • Cape - bought from Major. I assume it is Woodman canvas design. I don't know who weathered it, but whoever did it used RafalFett's template and did an awesome job.
  • Boots - MOW. Weathered by me
  • Toe spikes - Machine Fett. Weathered by me.
  • Braids - horsehair. I bought them off of Major. Might be Woodman, but this is unconfirmed. I am having him make me another pair because the blonde isn't blonde enough.
  • Shin Tools - scratch built from found parts except for the Aluminum Mitchell rods, which are replicas ordered from Mojo Fett (see Paterson Squeegee and Paterson Chemical Stirrer. It makes no sense not to make these from found parts.)
  • Girth Belt - Victory Canter. They make a brown, but it is the wrong color for my tastes. I used the dyeing method with the water-soluble latex stain. I then painted over with Rustoleum Ruddy Brown.
  • Ammo Belt - Delta 13 Mike
  • Pulce holster - Stormrider
  • Pulce 40 sidearm - Shapeways, design by RafalFett. Painted and weathered by me.
  • EE-3 - mostly davethebookie bronze cast. Finished by davethebookie.
  • EE-3 greeblies - disc for damper rods - Combat Baby. Shrouds - Combat Baby. Barrel Rings - Combat Baby. Damper rods - found parts. Molex - found parts.
  • EE-3 scope and scope rings - unknown 4 X 20. Japanese make. Bushnell rings.
  • Voice amplification system - Aker MR2300.

There are so many small piece on the outfit. I am sure I am missing something. Those are the major items. I don't want to think how much I spent. There are several items that I upgraded before even finishing the costume. I was not planning on being so anal retentive. I wanted good enough to trick your average Star Trek fan. I ended up with something a little better.


This thread is more than 7 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top