Sidearm / Holster set or molds for sale.


Stormrider

Well-Known Hunter
------------------------------ EDIT PLEASE READ --------------------------------------------
My grandmother died yesterday, and I am going to attempt to clear this up as quickly as possible as I have a lot of things to deal with in the coming week. I am sending out pm's and should have all holsters shipped asap. I made most of the pulls yesterday. I expect the mold en-route to chris by the weekend.

---------------------- EDIT - Negativity removed ------------------------------------------
Synopsis - I made a poor judgement call based on poor judgement, and miscommunication. It could have easily turned out bad for me from a recasting stance but FP (chris) took the high road, and showed me an amazing amount of compassion. A bad project turned worse, FP is allowing me to recoup my money for this project (which was a cast of his holster) out of generosity, and then I am sending him themold.

The list CLOSED for the holster, and limited to the names listed below. They will all ship this week. (7 are done).

Italianninja - SHIPPED 4-27
Boba68 - SHIPPED 4/28
TrooperDYL - SHIPPED 4/28
Ultraviolet - SHIPPED 4/28
RedArc - SHIPPED 4/28
Fett seven -> withdrew -> Nerf-Herder replaced SHIPPED 4/29
Boba mike -> no answer

Clonecollector holster/sidearm HOLDING FOR BOTH PIECES
DarthMalice - holster/sidearm HOLDING FOR BOTH PIECES

THERES ROOM FOR 1 MORE in the 10. If you want it PM ME!


PM's are incoming.

When this list is complete, there may or may not be life on the mold. Chris is working on a V2 mold. I dont not now if he will offer pulls from this mold or just library it, but I am unable to take any more requests out of respect for my arrangement with chris to clear this up.

Again, hats off to chris for being more of a standup person and showing more compassion than even I believe was necessary.
 
Last edited by a moderator:

Stormrider

Well-Known Hunter
Holsters are roughly 100 USD.

Righ now I have all the snaps/screws EXCEPT the one that goes through the snap down on the holster its self. I havent found a shank long enough. Chicago screws makes a screw together one. Ill look at ordering them.

Shipping in the us is roughly 10USD, shipping to the UK area is almost $40 usd.

Australia is likely the same. Maybe a little more. The box isnt huge, so theres no telling (prices go awry).

I will start a list for a run. I dont intend to do these for a long time. I need to get my $ back I spent/was promised, and then move on to the next project. Ill say the list will be a max of 15-20 or mold failure whichever comes first.

I have pulled 3 from the molds thus far.
 

Stormrider

Well-Known Hunter
Kaane, that I know if its a pulse 40. The logo matches the pulse logo and the holster says technosub. I cant find a pic of the pirarte 40 so I cant rule it out. I will post a pic of th original.

Ok, im going to order the last of the button pieces, and figure on making 10 of them. Ill put up a list of names up top for holsters.

Thanks all!
m2
 

KaanE

Well-Known Hunter
The diferences between the Pirate 40 and the Pulce 40 are that the Pirate 40 has a clear plastic tip while the Pulce is metal, and also that the Pirate 40 has a solid trigger guard while the Pulce has a hole in the middle all over the trigger guard.

Both are exactly the same except for these differences.
 

Stormrider

Well-Known Hunter
The diferences between the Pirate 40 and the Pulce 40 are that the Pirate 40 has a clear plastic tip while the Pulce is metal, and also that the Pirate 40 has a solid trigger guard while the Pulce has a hole in the middle all over the trigger guard.

Both are exactly the same except for these differences.


It is a pirate then. The tip is clear, and I thought both 40's had a solid trigger guard, and it was the 60 or 90 that had a split. Though admittedly I never researched i fully. I caught both of these projects by agreeing to do the molds for someone else and ended up buggered.

So as Kaane has pointed out its the pirate not the pulse.
 

KaanE

Well-Known Hunter
But... don't get me wrong. Both Pirate and Pulce are exactly the same in shape and dimensions. If I had money I would for sure buy one of yours. You're the master with moldmaking and resin casts. Your casts are always the cleanest!
 

Stormrider

Well-Known Hunter
This cast is about a 7 out of 10. Im not happy with the parting line. Its a little thick on the underside. But for $100 I figured I would offer up a 'budget' fet kit of sidearm and holster.

The holster on the other hand, is immaculate. And the rubber is superb.

The guns would prob be 100 shipped, the holsters 110 shipped, 200 for a set. Im going to make a new 'individual piece' mold, like my webleys. I just have to find the time. Soon though. very soon.
 
Top