Machined Boba Fett Jetpack Missile and EE-3 Barrel Mounts Rifle Parts

clmayfield

Active Hunter
Missile looks awesome, but it must weigh a ton! How much of the jet pack are you going to make aluminum?
 

CombatBaby

Well-Known Hunter
Just the missile and normal stuff. Might do the thrusters too since i can hollw them out.

Sent from my SM-N920V
 

clmayfield

Active Hunter
Cool. I love your aluminum ESB flamethrowers. Too bad I missed out on the run. I love aluminum parts in general. They just feel more substantial.
 

LostDreams

Jr Hunter
I can't help but think of how crisp and great this would look on a chromed out Fett suit!! Stainless steel used on the machined parts, or dipped chrome thereafter, but this looks too good to paint! Nice progress!
 

CombatBaby

Well-Known Hunter
Yeah that rocket looks great! How do you plan on going about with the fins?
I will be trying a new design on the top. It will be counterbored and slotted to allow 3 separate machined fins to slide in. They will be tensioned internally.

Sent from my SM-N920V
 

CombatBaby

Well-Known Hunter
I may doing a small run of the barrel mounts in the future if anyone is interested. Since they will be painted I could also offer them in aluminum and just adjust my cutting speeds. I was also thinking of offering a more deluxe kit with metal molex connectors (with some artistic freedom) and maybe scope mounts if I can make a decent design for metalworking.

Sent from my SM-N920V
 

Funkyred

Active Hunter
Preferred Vendor
I would be very interested in the scope mounts and molex's if your are creating a list
 

CombatBaby

Well-Known Hunter
Once i finish prototypes i will make a thread in the cargo hold and organize a run for anyone interested. Thanks for thr kind words

Sent from my SM-N920V
 

jbdubz

Active Hunter
I may doing a small run of the barrel mounts in the future if anyone is interested. Since they will be painted I could also offer them in aluminum and just adjust my cutting speeds. I was also thinking of offering a more deluxe kit with metal molex connectors (with some artistic freedom) and maybe scope mounts if I can make a decent design for metalworking.

Sent from my SM-N920V
looking good! will the front mounts have the two screws already installed, holes drilled or will those details be left up to the buyer?


Sent from my R2 unit
 

CombatBaby

Well-Known Hunter
i am interested in a rocket will u produce a few of these?
I am going to be spending more time on the prototype to try to capture the best appearance while keeping machine cost down. I have to be honest I know it will still end up being expensive and I may only do one run. But I will keep everyone updated.

Sent from my SM-N920V
 

CombatBaby

Well-Known Hunter
looking good! will the front mounts have the two screws already installed, holes drilled or will those details be left up to the buyer?


Sent from my R2 unit
I will be attempting to incorporate as much mounting hardware as possible. If the kit is just molexs and barrel mounts I will make sure all of that has supporting hardware and using a set of resin or real scope mounts from another source integrates well. I believe someone did a run of scope mounts but I have to double check that

Sent from my SM-N920V
 

jbdubz

Active Hunter
I will be attempting to incorporate as much mounting hardware as possible. If the kit is just molexs and barrel mounts I will make sure all of that has supporting hardware and using a set of resin or real scope mounts from another source integrates well. I believe someone did a run of scope mounts but I have to double check that

Sent from my SM-N920V
Sorry dude, my bad, not what I meant. At the bottom of the front mount there are two screws.
mount screws.png

Also, the mount is not a complete circle around the flash tube
mount gap.png
 
Top