Brokk's Jango Fett Build (WiP)

Brokk

Active Hunter
defo6qs-e3ecaa3a-7d2e-4541-b1f4-d1d9b043618b.png


With my Pre Pro 2 Fett wrapping up, I've debated on what Fett would be next as I want to do one more, and likely my last for a long time. And as it happens to be anniversary of Ep II: AoTC at the time of this post, I'd like to kick off the build thread.

When I was a kid, Ep. 2 AToC solidified my love for Star Wars and was loving the Fett's so much at that age (And still do). With the addition of the Star Wars Bounty Hunter game, Jango had a huge impact on my imagination along with Boba.

---

~Projected Parts List~

- Helmet: AoTC Lineage Cold Cast ✅
- Painted: In progress

- Upper Body Armor:
Cruzer Cold Casts ✅

- Gauntlet kit: 3D printed

- Girth Belt: Delta Mike

- Ammo Bemt: Delta Mike

- Gun Belt: Delta Mike

- Westar 34's: 3D print ✅
- Painted:

- Lower Body Armor:
- Cod: Cruzer CC ✅
- Thigh plates: Cruzer CC ✅
- Knees (Ordered via BM)
- Shins (Ordered via BM)
- Boot Armor: Cruzer ✅

- Boots: ✅

- Flight Suit: Arkady

- Leather Flak Vest: ?

- Leather Gloves: ✅

- Jetpack (Z6): ?

- JP Harness rig: ?

***Will be checked off as parts are obtained.
 
Last edited:

santakillz

New Hunter
Welcome to the party! Looks like we got about 3 maybe 4 active builds going on for Jango right now. Not sure if you're looking for any part suggestions, but I threw a few of my parts below that I am super happy with. The MoW jetpack is decently heavy and looking back a 3d print might have not been a bad option. Lot more prep work for sure though!

Gauntlet - DC Props (facebook)
Boots - Crow Props (website)
Flak Vest - Bobamaker (website)
Gloves - Lands End Womens Navy Blue (amazon)
Z6 - Man of War (website)
 

Brokk

Active Hunter
Welcome to the party! Looks like we got about 3 maybe 4 active builds going on for Jango right now. Not sure if you're looking for any part suggestions, but I threw a few of my parts below that I am super happy with. The MoW jetpack is decently heavy and looking back a 3d print might have not been a bad option. Lot more prep work for sure though!

Gauntlet - DC Props (facebook)
Boots - Crow Props (website)
Flak Vest - Bobamaker (website)
Gloves - Lands End Womens Navy Blue (amazon)
Z6 - Man of War (website)

Thank you very much for the directions regarding the gauntlets- I used to have a set of DC's for Boba, nice to know he does them for Jango.
 

Brokk

Active Hunter
Looks good to me! What straps did you go with? I like the detail in the middle on yours way better than the stuff I picked up.

Brant is correct, it's the Dritz brand with a green label
__________________
__________________

Today I took sometime to focus on the Cruz armor parts I have in hand. They came a bit too weathered in my opinion from the previous owner, easy fix- I really dig the subtle weathering with Jango more. So I went to work with a magic eraser to remove some of the weathering and left a little behind; then went over the pieces again with steel wool 0000.

Knee guards and shin plates have been ordered via Bobamaker.

20220520_141339.jpg
20220520_141942.jpg
20220520_142021.jpg
20220520_142532.jpg
20220520_142605.jpg
 

Brokk

Active Hunter
Indeed

______


Working on the helmet- this was previously painted in another color scheme. Adapting it for the build, make is a Jango Cold Cast Linage sculpt from WastedFett.

The colors have been removed carefully, I masked off all the cold cast bordering the color as to not damage or scuff the luster, which was a success.

20220523_201644.jpg
20220523_201703.jpg


Been playing around with some blues.
- Krylon Ocean Blue
- Testors Bright blue

Screenshot_20220522-205324_Instagram.jpg
 

Brokk

Active Hunter
Helm paint day. Upper cheeks and ears, used Ace Hardware brand Brite Blue in place of Rustoleum Royal blue.

Photo 3 taken with flash on.
20220528_153215.jpg
20220528_162440.jpg
20220528_213502.jpg
20220528_213544.jpg
20220528_213600.jpg
 

santakillz

New Hunter
Did you go with 1/8" for the pin stripe? Comparing the your bucket and mine, mine do seems a little thicker, but it may just be placement as well. You have a steady hand to get them that straight, I will be redoing my soon.

Looks amazing!
 

cbrant

Active Hunter
Did you go with 1/8" for the pin stripe? Comparing the your bucket and mine, mine do seems a little thicker, but it may just be placement as well. You have a steady hand to get them that straight, I will be redoing my soon.

Looks amazing!
You want 3/32nds - Cowles Products makes a nice pinstripe tape for it. It was the Cruzer recommendation as well.
 

Brokk

Active Hunter
Did you go with 1/8" for the pin stripe? Comparing the your bucket and mine, mine do seems a little thicker, but it may just be placement as well. You have a steady hand to get them that straight, I will be redoing my soon.

Looks amazing!

Ya they're 1/8", will double check tho. I can't claim the striping was my work- they were already applied. CRL states 1/8", so I'll likely stick to that as I'm hoping to get it approved

-----

Today, I recieved the Westar 34's 3D printed in resin, by Corellia Creations. They're the Big Fred Custom files. Incredibly smooth, almost no clean up to do. Currently researching how I'm going to chrome them.

Also got some slim fit Navy blue leather gloves.


20220601_175357.jpg
Screenshot_20220601-185641_Instagram.jpg
20220601_185128.jpg
 
Last edited:
Top