Han In Carbonite: In the rubber

I'm in...

LMK if it is possible the way I mentioned (only the "textured" area is enough, as you said, the flat border around the carbonite isn't necessary to cast).

Rigid cast in 3 or 4 resin sections, all shipped to europe.

If it isn't possible in any way to do it in resin or fiberglass backed up resin (into 3 or 4 sections), then I will settle down for a rubber cast...but resin would be top notch!

cheers
 
I can try a resin, however, I would have to cast it as one piece, and then slice it with a ban saw, id have to see what I could do.

Theres no way to cast it in three sections, unles I made some silicone dividers. Which wold be difficult.
 
I am interesed in the rubber, including the sides. Could you please (whenever you have time) calculate shipping to Europe?

Thanks

Regards

Alfredo
 
Yep, like I said last week via PM before I left for vacation, definately want in for a gunmetal to Abbotsford, BC, Canada.
 
Because of the price of making and shipping these, its gonna have to be verified paypal to verified addresses. So verify yourself now! It ony takes a day or two!

Ill whip up the list soon.

Im going to whip up some silicone 'helpers' to help me make these things a little quicker.

Mondays the day it all happens.

M2
 
I like the rubber version. The material like the knees would be great. Very firm.

Me too!!!

Or if there was a possibility of a lite version like the helmet interiors :confused

I say this because I wouldnt have the room for a fully boxed HIC but one that I could hang on the back of a door like a poster... :love

How much would the rubber weigh for shipping I wonder...

Dave
 
I could probably do a foam version like the inserts. The front in rubber is roughly 20-22 lbs. The hands and face and toes are pretty much solid. the rest is 1/3 to 1/2 inch thick.

The one you see is rubber, but im going to make dividers to only pour it to the edge of the texture next time. So i can use the extra rubber on the 'details'. To make a full sized replica, you would want to cut it at the texture and 'inset' it anyway. If you wanted to do it right.

Soooooo much to do, so littl time:)
 
I can try a resin, however, I would have to cast it as one piece, and then slice it with a ban saw, id have to see what I could do.

Theres no way to cast it in three sections, unles I made some silicone dividers. Which wold be difficult.

As I've said, if it's impossible without doing annoying extra work then I'll take a rubber version.

Just forget the resin and the cutting...I'll settle down on a rubber version.

My paypal account should be verified. Just lmk when you take payments (including an international shipping qoute).

cheers
 
To clarify the paypal thing, if you have bought from me before, it shouldnt be a problem.

I am getting quite a few 'never posted' and from 'zimbabwe' people messaging me.

There is a high level of tr4ust on this, with just shipping and materials costing me 200 right off the bat.

People with good reputations here need not worry, no reputation people shouldnt have a problem getting verified:)

I hope that clears it up.

I think the rubber will be a lot more firm and solid than people thing. Ill take more pics tomorrow.
 
haha. Tell him I said:

Hurry Mr. Hello
I am for opportunity for him. Simply with haste paypal me $400 USD funds prompt. I immediately as can make appropriate shipment of said goods.
 
This thread is more than 10 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top