Apollo's Weathering Tutorial

Apollo

Hunter
I’ve been asked a couple of times for a weathering tutorial so I’m going to try to catalogue my process as best I am able.

The first thing to do after the armor is all ready for paint is to decide what kind of base metal you are going to use. I have always used different kinds of silvers, but I have seen somebody who used plain grey to emulate duraplast and I’ve seen bronze look really good as well. For a while I used spray paint and there are a lot of options for that. What really matters when using spray paint is that you use the same brand that the rest of your paint is going to be

Recently I have begun to use rub n buff metallic wax for my base coat. I think this might be overkill on my part since the metal color doesn’t matter a whole lot unless you don’t paint over it, but I’m practicing for a Jango. There are several different shades of gold, copper, silver, and pewter available; to this point I have only used silver and pewter. Rub n buff also requires a lot of prep work before it can be applied. You need to prime your armor, wet sand at 400, and wet sand at 1000. Better results can be achieved by wet sanding at various other grits going up to 2000 and priming in between each wet sand.

After your armor is all sanded apply a bunch of small globs of the rub n buff all over the pieces and begin rubbing it vigorously with the palm of your hand. Rub n buff is a wax so it needs heat to melt it to the primer. You will probably get smudges and places where the rub n buff will just not stick. This is very frustrating, but it happens to me every time. At this point you can either: resand and start over, try applying more rub n buff, take the armor as is and move on to the next stage.

After the rub n buff is on you can make it very lustrous by taking an old t-shirt and buffing it very hard. I spent 10 minutes on each piece when I did this and the results were pretty cool; I could see my own reflection in the armor!

Here are pics of pieces rub n buffed using various methods

Pewter (I have used this color a few times and I have never gotten really good results like I have with silver. I’m not sure why)
DSCN0764.jpg

DSCN0763.jpg


Silver buffed (in the ab plate of the first picture, that’s not a large smudge; that’s actually the reflection of me taking the picture)
DSCN0765.jpg
DSCN0766.jpg



Silver not buffed
DSCN0767.jpg

DSCN0768.jpg


And a couple of comparison shots
DSCN0769.jpg
DSCN0770.jpg


Now on to the painting! This is definitely my favorite part of the whole costume building process. I use layered weathering which means that I have a basecoat, and then I paint on all the layers while masking off portions of the armor between each layer. I used to use toothpaste and then I used rubber cement, but now I use liquid latex masking fluid. This stuff costs 15 bucks for a small bottle so toothpaste or rubber cement are really much more cost effective.

DSCN0792.jpg


Apply your masking fluid to wherever you want the metallic color to show through. Remember that you want to leave room for your aesthetic primer so make your damage a little smaller than you see it in your mind. Weathering needs to be random, but it also needs to make sense. The edges of metal plates weather a lot faster than the inside; the same goes for raised surfaces. When doing the rest of your weathering make sure to mix up damage type (scratches, scrapes, dings, blast marks), size (small scrapes, long scratches, etc.) and placement (even spaced damage all over the armor doesn’t actually make sense). If your armor had any stripes or sigils on it make sure that the paint chipping overlaps them too. It’s a little thing, but showing that individual bits of weathering are not confined to certain colors makes the whole piece look much more realistic.

After you’re done masking the base metal apply a few coats of your aesthetic primer. After is dries mask off areas of the primer and apply a few coats of your topcoat. At this point you can begin to rub the armor with your finger to remove the masking fluid (or wash your armor under a faucet to get rid of the toothpaste) to see how the weathering looks. Pat yourself on the back; the hardest part is done!

*on this set I used Krylon Ruddy Brown primer in between my aesthetic grey primer and the burgundy topcoat. It can make your armor look slightly rusted, but it should only be used sparingly or else it loses the effect*

At this point you can begin to paint on any stripes, markings, sigils you want. If you’re going with basic geometric shapes it’s fairly easy to just make their outlines with blue painter’s tape, but detailed designs are more difficult. I’m going with 2 stripes going down the armor on this set so I just lined up all of the painter’s tape and then used ripped up pieces of newspaper to cover the rest of the armor. I applied my masking fluid and then laid down the ivory paint for the stripes. I remove the masking fluid before doing sigils and designs because after enough layers of paint the latex is really hard to get up, and because repositioning the painter’s tape always rips up some of the masking fluid anyways.

Here are the stripes painted, but before the masking fluid is removed
DSCN0772.jpg


and here is a shot with the latex removed
DSCN0786.jpg


some close-ups of the weathering
DSCN0787.jpg

DSCN0788.jpg

DSCN0789.jpg

DSCN0790.jpg



After all of your painting is done the last part is topical grime weathering. I’ve been pleased to see lately that a lot more people are taking the time to do this step on their armor, and it makes a huge difference. It’s one of those things that people might not be able to put their finger on, but they will notice if your battle scarred mando is perfectly clean.

There are a couple different ways to achieve the dirt on your armor. Misting with spray paint can look really good if done lightly enough and airbrushing is also very nice. I’ve seen people use artist’s chalk and even actual dirt as well. Another very popular method that I have never tried out is blackwashing which involves mixing water and black paint and spraying it on your armor. Which method you choose will be determined by what materials you have easily available to you and what environment your mando predominantly works in. Ash and soot look different from dirt.

I use mixtures of acrylic paint, and on this set I just need basic dirt colors. Black, burnt umber, and raw umber are mixed in equal parts and then applied with a napkin. The exact technique takes practice to get down, but basically I add a little bit of paint and then wipe it off and then add some more and maybe wipe it off. I’ll keep on going like this until I get patterns that I like. The key is to get the paint stuck in the crevices created by all your layers of paint since that’s how real dirt would accumulate. Remember to be random here too, but apply the most dirt on the edges of pieces and in those crevices.

DSCN0791.jpg


I learned this particular topical weathering technique from SEEKER on TDH and he has a video that shows it near the end (about 6:13). His technique works well for light weathering whereas I generally go for something a bit heavier

Some close ups of the grime in the crevices

DSCN0803.jpg

DSCN0802.jpg

DSCN0801.jpg

DSCN0800.jpg

DSCN0796.jpg

DSCN0795.jpg

DSCN0794.jpg


And that’s it! Here are some pics of the finished pieces so you can see how it comes out.

DSCN0808.jpg

DSCN0806.jpg



PM me with any questions, or ask here so other people can see too.
 
Last edited by a moderator:
Wau man, you have left me without words friend, I have to work in my gauntlets (ROTJ version) and I believe that from here I will study as making it, thank you!!!!!!!!!
 
Awesome effect! Okay, question: Are you using any fixatives to hold the paint on? Like a light spray of Krylon matte fixative?

Thanks
Deunan Shiruba
 
I used a clear coat once before to help the paint adhere to the rub n buff, but it made the rub n buff not look as authentically metal so I skipped that this time and I didn't have any trouble. The key is to just lay down a ton of coats so that it won't come up easily. If I could go back I think I would lay down a coat of primer in between each color to make the colors more pure, but that's just a small thing
 
Wow! That's some amazing weathering there, bud! Is that a single thick coat to make the chipped paint look so distinctly layered, or several coats?
 
thanks for the kind words guys.

There are 3 or 4 coats of grey primer, 1 coat of the ruddy brown primer, at least 10 coats of burgundy, and 5 or 6 very thick coats of ivory. Using so many coats is what makes the paint chipping and grime weathering look the way it does
 
hello, I was wondering where I can get "Rub & Buff"? I live in Canada and I checked in my local Canadian Tire store today but they don't carry it. The guy I was speaking to was looking at me like I was an alien or star wars character or something.

But seriously, where does one find this?

Thanks
 
I get mine at A.C. Moore; if you have any kind of craft/hobby store that's where I'd check. My store keeps it with the picture frames
 
Whoa, awesome tutorial! I've had trouble painting/weathering before, but this should help immensely. Thank you very much for posting this!
 
Hey Apollo, just wanted to say thanks for the excellent tutorial. I just painted up my kids trashcan armour (link here) and although I made a ton of mistakes along the way I'm pretty happy with the overall look. I also learned some important lessons:

1: Wait for the paint to dry. 20 minutes isn't long enough.
2: Don't try to reshape the plastic once you've painted it (cracked the shoulder bell paint this way).
3: The wind will blow newspaper onto your freshly sprayed armour parts as soon as you look away. But that's okay because sanding it all down and starting again is so much fun..
4: The same also goes for insects. Mmm, bugs!
5: Wait for the paint to dry!!
6: Weather all the parts in one go so that the acrylic mix is the same colour and consistency.
7: Removing the masking fluid between colour layers and then re-applying fresh fluid to the same areas (plus a little extra) seemed to produce better results than layering paint and masking fluid and trying to rub / peel the fluid off afterwards (like you said, it can be a pain to shift it under several layers of paint).
8: Finally, WAIT FOR THE DAMNED PAINT TO DRY! Fingerprints in tacky paint are baaaad.

So thanks again and I'm actually looking forward to painting the backplate and cod. Making them, not so much. But painting? Yes :D
 
I think that ALOT of people here should study this thread really good.

You' re work is amazing. I feel inspired by this and I' m certain I' ll try this layered approach aswell.

My weathering is all topical, which is much easier to apply, but doesn' t get the same awesome results as this kind of weathering.

Simply amazing!! I hope alot of custom builders take this thread to heart.
 
Boy am I gad I stumbled across this. I'm currently in the process of figuring out all of the details to my first custom Mandalorian. Nothing has been on my mind with regards to this project more than how I'm going to paint the armor and whether or not to weather it (not much experience in this area, hence the indecisiveness). I'm actually looking forward to trying my hand at weathering now after seeing this! Now all I have to do is get the armour...
 
Glad I found this thread! This is exactly the information I was looking for. Your work is very inspiring.

Kudos to Siygess for his tips, too; I've had so much trouble spray-painting outside that I've given up entirely, and instead converted my bath and shower into a spray alcove.
I never used the bathtub anyway. -_-
 
This thread is more than 11 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top