Full Size Helmet Interior

Yep, that's right! As soon as the molds arrive here, I'll take a look over everything and figure it all out. After that, I guess we'll get right into production. Stay tuned! ;)

Later,

MJC.
 
Definate buyer here C-Dude. Can add me to the pre pre presign up list for the future preorder list of the somewhere way out in the not so near future hopeful possible sale of those great looking interior kits. Great job MS and great idea.
 
do you guys think this would all fit in, slightly modified so a servo unit for the RF will fit behind.. would be a good way to hide the circuit boards :)

thats assuming i manage to actually get my armour... due for delivery early this week and no arrival nor correspondence with seller. :-S
 
Well if you take a look at this photo:
attachment.php

... I bet you probably could modify it a little to make room for a servo. It would probably mean cutting off the top portion of the right hand side piece and maybe carving out the back sides of some of the other pieces to allow room for the circuit boards etc. you mentioned. Probably not too hard.

Bye for now!

MJC.
 
Has anyone had any troubles fitting the kit in a BobaMaker helmet?

I've got a BM and I'm a little concerned about squeezing my big noggin in there after installing the kit.

Anyone think the size of the BM helmet could be a problem?
 
I've got it in a MSH2... the 2nd biggest bucket (next to an MLC) and I've gotta say it's a tight fit. My nose get's squished. :lol:

And thanks to Laan... I've now got a COMPLETE set once again. THANKS BUD!
 
webchief said:
I've got it in a MSH2... the 2nd biggest bucket (next to an MLC) and I've gotta say it's a tight fit. My nose get's squished. :lol:

And thanks to Laan... I've now got a COMPLETE set once again. THANKS BUD!
Click to expand...

That is due to the squished back... not the over all size.. it is deep vertically but when it comes to room from the back of your head to the front visor there is not as much room as you might think from looking at it. Big is a relative term when it comes to some of the helmets... :)
 
MarrowSun,

I know this thread has not been active for a while, but I have a few questions about how you shaped/sclupted the pieces

1. did you carve them out of foam rubber from the start, or use something else to get the detail.

2. what tools did you use to sculpt with kinfes, dremel bits?

any help would be appreciated.
 
SR has a post for interiors in the cargo hold but he hasn't posted an update in over a month so who knows if he is still going to do them.
 
This thread is more than 11 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

Citiyard
failed attempts on interior electronics
Replies
0
Views
179
Citiyard
Citiyard
starsaber25
Kill Stripe Size
Replies
10
Views
998
starsaber25
starsaber25
E
European helmet makers
Replies
7
Views
454
BudaFett
BudaFett
Wraithy1901
Painting a helmet
Replies
3
Views
609
Wraithy1901
Wraithy1901
Boba Fret
EFX interior solutions
Replies
2
Views
1,100
WhiteShadow
WhiteShadow

Similar threads

Citiyard
failed attempts on interior electronics
Replies
0
Views
179
Citiyard
Citiyard
starsaber25
Kill Stripe Size
Replies
10
Views
998
starsaber25
starsaber25
E
European helmet makers
Replies
7
Views
454
BudaFett
BudaFett
Wraithy1901
Painting a helmet
Replies
3
Views
609
Wraithy1901
Wraithy1901
Boba Fret
EFX interior solutions
Replies
2
Views
1,100
WhiteShadow
WhiteShadow
Back
Top