DIY ROJ EE3 Carbine

Get a full size toy or airsoft pistol (preferably a revolver), get a episode 2 or 3 anakin skywalker electronic lightsaber, a few small sheets of sintra, various assorted tools, primer, rub n buff, aluminum color paint, dark gray paint, plastic epoxy, caulk, a few sheets of reasonably thick wood, a saber saw (or if you cant afford one, a hand saw), a hairdryer, and a brain.


Cut the lightsaber just at the blade emitter, and throw the blade emitter away, leaving you just a hollow shaft. put the revolver in the shaft, and stick in with plastic epoxy, fill gap with caulk, sand.

take sheets of sintra, heat with a hair dryer on hot for about 5 minutes, to get it floppy, then curl into the shape of a cone, cut the tip off, leaving a hole. Glue to the end of the lightsaber opposite the gun, caulk and sand.

cut out a boba fett stock template (found here: http://www.propaholics.wolfchasers.c...ev%20Ae121.gif) by printing it out and cutting it with scissors. outline it onto your sheet of wood, then cut it out with a saber saw or hand saw, then sand. measure the width of the end of the stock thumbhole branch things, then cut those size holes in the grip of the pistol. Stick it in there, fill with epoxy, let dry, cover with caulk, and sand.


add a scope (however you want), some greeblies, then paint it however you want (there are a million weathering tutorials) and viola, you have yourself a passable EE-3. feel free to mess around with this recipe however you want, it's just a rough draft
 
wow...Gonerebel....you're place on the A-Team will always be assured!
dee dee dee dee -dee dee dee
Mike
 
Last edited by a moderator:
Get a full size toy or airsoft pistol (preferably a revolver), get a episode 2 or 3 anakin skywalker electronic lightsaber, a few small sheets of sintra, various assorted tools, primer, rub n buff, aluminum color paint, dark gray paint, plastic epoxy, caulk, a few sheets of reasonably thick wood, a saber saw (or if you cant afford one, a hand saw), a hairdryer, and a brain.


Cut the lightsaber just at the blade emitter, and throw the blade emitter away, leaving you just a hollow shaft. put the revolver in the shaft, and stick in with plastic epoxy, fill gap with caulk, sand.

take sheets of sintra, heat with a hair dryer on hot for about 5 minutes, to get it floppy, then curl into the shape of a cone, cut the tip off, leaving a hole. Glue to the end of the lightsaber opposite the gun, caulk and sand.

cut out a boba fett stock template (found here: http://www.propaholics.wolfchasers.c...ev%20Ae121.gif) by printing it out and cutting it with scissors. outline it onto your sheet of wood, then cut it out with a saber saw or hand saw, then sand. measure the width of the end of the stock thumbhole branch things, then cut those size holes in the grip of the pistol. Stick it in there, fill with epoxy, let dry, cover with caulk, and sand.


add a scope (however you want), some greeblies, then paint it however you want (there are a million weathering tutorials) and viola, you have yourself a passable EE-3. feel free to mess around with this recipe however you want, it's just a rough draft
Do you have any pix of a gun made in this fashion?
 
please keep in mind i did not make this, it was just made using my method:

ee1a.jpg
 
This thread is more than 14 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top