Darktrooper Progress Thread 8MAR2011: Getting back to it

lookin good, its about time this thread hit 100 posts :)

Im confident to say that there were no reported injuries caused by overloading computers from the first page. We are safe from the carnage thats is dangeroulsy loading a web page containing too much data!

-tubachris
 
Last edited by a moderator:
Will the helmet rear be a one piece cast, or a multiple part?

I'm concerned that the sheer size of the helmet rear will be too much for the casting material when you suck the air out.
 
Last edited by a moderator:
Will the helmet rear be a one piece cast, or a multiple part?

I'm concerned that the sheer size of the helmet rear will be too much for the casting material when you suck the air out.

To answer lloyd, very durable. A lot of people on here prefer it over fiberglass because it won't chip or crack as easily because it has some give upon impact.


Now on to mandolore's comment. I think he will be ablet pull these on a single sheet as long as he has nothing else on the forming table. I know stormtrooper ab plates, back plates, and boba fett backplates are done in single pulls. This is a lot smaller in terms of space on the forming table, it's just more vertical. I think if he heats the plastic well enough it should be fine.

-=QuinN!
 
Last edited by a moderator:
To answer lloyd, very durable. A lot of people on here prefer it over fiberglass because it won't chip or crack as easily because it has some give upon impact.


Now on to mandolore's comment. I think he will be ablet pull these on a single sheet as long as he has nothing else on the forming table. I know stormtrooper ab plates, back plates, and boba fett backplates are done in single pulls. This is a lot smaller in terms of space on the forming table, it's just more vertical. I think if he heats the plastic well enough it should be fine.

-=QuinN!


Yeah, I thought about this too, and was afraid of the plastic tearing at the highest point. I realized however, that the heated plastic stretches and in spots of the plastic that arent being used would become thinner because of the stretching. Im sure that it will be fine, I plan to use .80 thick plastic, or should I go for something thicker?

-tubachris
 
Last edited by a moderator:
I need a consensus..

I was thinking about the hand guards, and realized that in all the reff pics from the game, the hand guards look like they just put a blob of grey over it. Becuase of that, I was wondering if I should make them standard TK from ANH, or clone hand guards. What do you guys think? Im leaning more towards ANH version only because the DT is from that general era of the empire. Would make more sense, yet, a majority dosnt cause most of it is clone!

-tubachris
 
Last edited by a moderator:
My personal (and mostly random opinion) is to stick with the ANH. I would imagine that the game designers, though referencing old dark forces pictures, probably wouldn't have paid attention to the hand guards.

The Dark tropper Phase two in DF was essentially stormie armor (with minor differences), so I would just go with that.
 
Last edited by a moderator:
Thanks guys!

I have been wroking on the guants for awhile now, the hardest part being getting these dang boxes to cut and look good at the same time. I managed to cut out the boxes, all evenly spaced with the accurate amount, 12 boxes in total. I just need to gett some stronger files, instead of my puny, nail files which I still have from my Jango helm project. Thats it for now, im probly gona get some more MDF and start the second half of the guant and start the hands and biceps...

-tubachris
(Who's watching Fox, and still wonder's why Anna Nicole died like 10 minutes away from him...)
 
Last edited by a moderator:
Well, heres just a quick blurb.

I havent worked as much as I would have liked to for the past few days, been really busy. Right now, the guant top half boxes are cut and ready to be attached, just trying to figure how to level the boxes so its relatively flat to the guant. I think I may just sand the center portion so that it can just lay there. Im gonna also try to start the second half tonight as well.

-tubachris
 
Last edited by a moderator:
Good luck with your Gauntlets, I would not even try to make a set of them just yet. I'm getting mine off another Mando, just waiting for them to arrive.... any how just take your time and i'm sure they will look good. Can't wait to see a pic of them.......
 
Last edited by a moderator:
I have been busy yesterday, but managed to work on the top half for a bit. Its pretty much done minus the small areas I need to re-fill with the durhams. I was gonna post pics last night, but wasnt able to. I will though around noon. Gonna start the bottom half later today. I love half-school days.

-tubachris
 
Last edited by a moderator:
Well, here it is. From a picture standpoint, its done as far as the look is concern, really, I just need to do a little more durhams work and some sanding. Other then that, I just to drill holes on the inside of the boxes so that the vaccum can pull the plastic into it so it appears better. Its not perfect however, but thats how we get better...



guantlettophalf2.jpg


guantlettophalf1.jpg


-tubachris
 
Last edited by a moderator:
This thread is more than 9 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top