ANH Tusken Raider Mask rebuild

Darth Voorhees

Well-Known Hunter
Preferred Vendor
Ok so i got a ridiculously good deal on a Tusken gear ($120 complete/shipped!!) right here on the dented helmet, so i jumped on it. It was all home made and not to bad. But me being the way i am, and loving to "rebuild" stuff, i decided to completely re-do the mask. I THINK its a poor mans kit (please correct me if im wrong any of you Denizens out there!)

So heres how it looked when i got it:
100_1820.jpg

100_1819.jpg

100_1818.jpg


Not bad but when i look at this reference pic....
Diamondtuskenclose.jpg

.... it looks way off.

One of the things i didnt like, was the "nose" (or i call em teeth) was too high up. I actually noticed most fan made Tuskens look like this. They dont look BAD, but they dont look "right" to me. I have actually started my own sculpt of a base mask, but thats for another thread lol. I also barely fit in it vertically. My chin was right up against the leather wraps on the bottom of the snout.

So i decided to strip this one down and do a kind of daring mod, hoping i didnt destroy the mask lol. Here it is stripped down:
100_1829.jpg

100_1832.jpg

100_1825-1.jpg


So my plan was to remove the "snout" and part of the bottom/sides and lower it about an inch. I know..daring...and i wasnt even sure it would work, but i went forward... and did this!:
100_1833.jpg


And here is my holding the pieces to what i was hoping i could get it to:
100_1835.jpg

100_1834.jpg


I then proceeded to CA glue and rivet spare HIPS to the sides to reattach the snout/bottom sides. I also added support in the nose area.We now have this:
100_1837.jpg

100_1838.jpg

100_1839.jpg


I then cut the hole for the Metal Nose (KINGJAWA) and tried to remove most of the leftover hotglue from the previous build.
100_1840.jpg

100_1841.jpg


I then taped on the old resin eyes just to get an idea what it would look like:
100_1842.jpg

100_1843.jpg

100_1844.jpg

Not bad.

So i now added some wire mesh to the open areas on the mask:
100_1845.jpg


i also attached what the previous owner had used as the back of the head (construction helmet i believe) but did it with elastic straps. It was just basically tape holding it together previously. I also padded out the forehead.
100_1846.jpg

100_1847.jpg

100_1848.jpg


Then i added the vinyl on the mouth/face areas:
100_1850.jpg

100_1849.jpg


I then added the leather and metal parts..all by KING JAWA.
100_1853.jpg

100_1852.jpg

100_1851.jpg


Then i started the wraps..trying to emulate the Peter Diamond Tusken as best i could.
100_1854.jpg


Here is how it came out:
100_1859.jpg

100_1858.jpg

100_1857.jpg

100_1856.jpg


What do you guys think? It was as close as i could get it to the reference. One of the things i want to address with my scuplt is the width of the bottom of the snout. Should be a tad wider to match the reference Tusken i posted. Couldnt do too much with this kit in that sense, but all in all im happy with how it turned out.
Heres a compare pic. Not quite the same angle heh. Obviously its not perfect, and still a bit off..but at the very least i got the eyes/nose ..well i always called em "teeth" ...spacing pretty close! Im happy with this bad boy for now!
compare.jpg
 
I still need to weather this overall, but i decided to do the mod on the mouth, and think its much better now. Heres what i did.

I made a "frame" to support the extra width with pieces of HIPS.

100_1866.jpg

100_1865.jpg


I then wraped it with craft foam to give it a flat surface and added the vinyl and the leather wraps. I also dyed the thin leather wrap dark red, and re-did the Nose. I think face wise, this is the best its going to get. Just want to add a few more wraps and weather it and im done.
100_1870.jpg

100_1871.jpg

100_1872.jpg


Heres a new comparison....the best i could get. The eyes are angled differently than the reference, but i think i got the overall look down:
compare2.jpg


Heres a compare of my original, my modded rebuild and the on set reference.
3compare.jpg
 
It looks MUCH better and I think the mouth build-up was well executed. Awesome!

Thanks Muad'Dib! I wish i could make the top of the head taller, but i don t have much more material for wraps so i think this is it with major mods on this. Im sculpting a base mask i hope will address all these issues i had. when thats all done, maybe ill give another go :)

Here it is weathered with the same shot for color comparison. :)
comparecolor.jpg
 
Last edited by a moderator:
Looking good. I built one of these a few years back and struggled a lot with the weathering on the wraps, it looked flat next to the reference photos. I started adding some subtle greens and reds and suddenly it just popped.
 
This thread is more than 11 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top