Ugly duckling RC helmet

butterbean

Active Hunter
DONE!!I scored this ....beauty......on Ebay for $70 bucks. I knew it would need serious attention but I was empty without an on going project. As you can see, the previous owner cut four holes on the front of the bucket which, if I'm not mistaken, are not supposed to be there. I started by "dremmeling" out the bottom which was really small. Could not fit anyones head in there. Next I sanded off most of the primer and then filled in those strange holes with Mighty Putty. That stuff is great by the way. I then tried to even out the interior thickness and put joint compound on the horribly visible seam on the back. More pics to follow, I have a grand vision and I cant stop now!;)
2723654800_9224f328da.jpg

2723656158_b2004fd42b.jpg

2723655528_88bbf5b154.jpg
 
Last edited by a moderator:
Outstanding! A good RC project to watch! Gotta love those commandos.

I wish I'd seen that for $70! Keep up the good work, can't wait to see more. ;)
 
UPDATE

Got most of the holes and pits filled in but the seam on the back still needs a little work. I had considerable grinding to do on the inside top of the visor opening to accomadate the EL wire that I just ordered. It will be a blue/green about 2.2 mm in diameter. I had to dremmel most of the "grooves" in the helmet because the "lands and grooves" were not at all consistant. I have also ordered a bright white LED for the right ear piece and I think I found a budget priced mirrored visor. Next step, more snading and priming.....
2730108374_ef2e0cf4d5.jpg

2729279495_9516b00b5e.jpg

2730109968_0104e9f182.jpg
 
Little update..... Went with black and obviouslly, battle damaged. Next comes the earpiece and LED light. Got the visor in the mail today. Alot thicker than I anticipated, not looking forward to cutting and installing. This is my first attempt at an RC helmet and I'm just winging it so comments or critiques are welcome:).
2743893319_62c5de3afc.jpg

2744734210_e2ae600c19.jpg

2744732852_6686c21ae8.jpg
 
Looking cool bro...
I just got myself an EP3 ugly duckling and it also requires some work! :facepalm

Nice job mate... (y)
 
Installed the lights, I hollowed out the right ear cap to fit a cheap LED snake light. I drilled a hole in the side of the bucket and fed the light through. I taped the snake light on the inside and left the push button toward the lower rear of the helmet for easy access. Next I installed the EL wire over the visor and secured the power source with velcro so it will be easy to change batteries.
Next, visor install with the "T-nut method" then padding. ALMOST THERE:wacko.
2747232321_2194a992f5.jpg

2747233459_be9d2d7cf0.jpg

2747234733_d9b6b9fac8.jpg

2747236065_6766288305.jpg

2748068116_ae8a7d5fda.jpg
 
Very nice! You can tell I'm a huge RC fan right? I reply to every post you're making here. LOL! I like the use of that snake light, I'll have to remember that one. :)
 
Thanks alot bro! I appreciate you looking there.

This project of yours is really apt for me. See, my next helmet model is rolling up soon, a friend is just finishing drawing up the blueprints for it.

It's the Republic Commando!
 
Secured the "t-nuts" with mighty putty, I was going to glue the visor in but now it is removeable, just in case of future damage. I know the "t-nut" install has been posted here before but it truly is the best way to put in a visor. Have to credit either spideyfett or batninja for that, can't remember which.
That pretty much does it! Republic commando Omega Squad reporting for duty!
2749864040_f159ce83b1.jpg

2749030377_b9024b123d.jpg

2749867130_ef1d87c35e_b.jpg
 
This thread is more than 15 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top