Ordo Te'skotah's Armor

Got bored...

188.jpg


three of the braids are hemp, two with bone skull beads strung throughout, the other with beads at the bottom. The hair is mine, the claws are there because of the claw marks on my armor... One of the claws is a bear claw, the other one I carved out of antler. I still need to get some horsehair and make a couple "wookie braids" to go with the rest.
 
Made this last night... went with a shape similar to my modified shoulder center pieces(Under the shoulder bells). I made it out of an old green couch cover, burned some hole in it, and threw a bunch of black dye on it. The black didn't take as well as I'd like, I may re-dye it, though dark green goes ok with purple and black . So I'm not sure yet:

189.jpg
 
Started on the gloves as well... Went with a pair of black leathers I had already, and leftover fabric from the cape for the padded sections. This is my first... and last... set of gloves I will ever modify. :angry

190.jpg
 
Good job! One of the best customs I've seen in a while. I like the use of the metal armour, you did a fantastic job with that. I also like how you modified the gloves. A lot of customs don't put that hard work into their suits. You've outdone yourself.
 
Thanks 8)

I've also done a little work on my "BlasTech DL-50" heavy blaster pistol:

194.jpg


It's nowhere near finished yet, but it's a start. Once I have it mostly finished, I'll re-paint it and the scope/mount and weather accordingly.
 
Another BlasTech DL-50 progress pic:

195.jpg


I scratch-built the scope out of found parts, aluminum scrap, a real lense for the rear "viewscreen", and an old charger connection pin for the front "sensor array". I'll get better detail pics after I finish them up.

The Blaster itself was also constructed completely out of found parts/scraps. The grip and main body are from an old .22 ramset nailgun, the rest of it is found parts, scraps, and a bit of sculpted JB weld to seal the seams between parts and fill gaps. Also, more detailed pics once it's finished.

*Edit* The barrel inside the main body is part of a real Heiland flashgun.
 
This blaster is so good; it's my favourite custom weapon I've seen here. If you were to cast it at some stage I'd want one, it just looks so SW!

I can't wait to see anything helmet related.
 
Thanks as always for the compliments!

Here's phase II of the paint job for the Blaster... still not finished, but getting there. I have to get a better drill bit to be able to mount the scope to the blaster... the metal the main body is made of is harder to drill than anything I've drilled so far. :facepalm

0.jpg


*If you get the "Red X of Death", please check back later. My picture hosting is having issues today. Thanks!
 
Last edited by a moderator:
This thread is more than 16 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

scorcione
Worried that..
Replies
5
Views
1,548
scorcione
scorcione
N
Cruzer’s Jaster Mereel helmet
Replies
0
Views
1,443
NROrtiz
N
Ellingsworth
Kal Skirata Shoulder Bell Trophy Wall
Replies
2
Views
3,600
Ellingsworth
Ellingsworth
N
Custom Mandalorian New Custom Mandalorian armor
Replies
17
Views
4,106
Barcode
Barcode
Mister Hyde
Other Bounty Hunter Idea for Alternative Mando Armor
Replies
0
Views
5,158
Mister Hyde
Mister Hyde

Similar threads

scorcione
Worried that..
Replies
5
Views
1,548
scorcione
scorcione
N
Cruzer’s Jaster Mereel helmet
Replies
0
Views
1,443
NROrtiz
N
Ellingsworth
Kal Skirata Shoulder Bell Trophy Wall
Replies
2
Views
3,600
Ellingsworth
Ellingsworth
N
Custom Mandalorian New Custom Mandalorian armor
Replies
17
Views
4,106
Barcode
Barcode
Mister Hyde
Other Bounty Hunter Idea for Alternative Mando Armor
Replies
0
Views
5,158
Mister Hyde
Mister Hyde
Back
Top