Female chest plate.

Fisheadork

New Hunter
Hey guys, I need help finding blueprints or tips for making a female mando chest plate. I'm not looking for a 'sexy' mando, but full tactical. Any help would be great!
 
i've always felt that if you're not trying to make a "sexy" costume then you shouldn't put boobs on the armor.
 
It is funny they did this considering whenever female Mandos were mentioned in writing, they made a point of stating that it was sometimes hard to tell the gender of the wearer.

Yeah, maybe in San Fransisco.
 
keyword "sometimes" I have actually seen several females who wear the standard plates... however a lot of them got tired of being mistook for a guy and started switching over to the femme plates.
 
That one has nipples... lol... I had to grind them out, then fill them. It sucked... bad... The plastic is 1/8"ish thick and gets hairy when you sand it.
 
Fortunately, the nipples aren't that pronounced, but more like just implications of them.

(why did I just say "fortunately"? I happen to like nipples ;/)
 
Yeah, but sanding it off goes straight through the plate. I ended up drilling 4 small holes around each portion where it broke through and had to stuff a wad of putty on there. The holes were for the putty to grip onto. Then, I did the bondo over that.

And guess what? When I got the primer on, the darn nips were still showing! I was sitting there thinking that I've never been so angry at a pair of breasts.

I probably should have done the filler first and tried to contour shape out, but I thought that would be an awful lot of filler for something thats going to be worn. Jokes on me, though. I almost ruined them... lol...
 
Last edited by a moderator:
put tape over the front of the nipples and bondo from the back. Take the tape off after it sets and it should be relatively smooth already and not need a lot of sanding. Even if it's a little thick on the inside, it shouldn't make them uncomfortable too much.

But I'm not a woman so I can't say for sure. ;)
 
meh I sanded the nipples down until I almost broke through, then poured resin in the back.
worked like a charm until i powersanded the bondo'd boobs and the resin plugs fell out due to the vibrations.
but now that the outside is bondo'd no real need for the resin plugs ... that look like perfect nipples, might paint them and stick em on my own plates as a joke.
 
Anyone play Mass Effect? Use Ashley Williams as reference.

ashley1.jpg
 
it's down to cup size really... if you can go for standard plates.
If you want or need cupped plates go with something understated and subtle like the above.
or go for the full on bombshell, with skin tight bodysuit and revealing cut away panels.. just don't expect more than drool
 
put tape over the front of the nipples and bondo from the back. Take the tape off after it sets and it should be relatively smooth already and not need a lot of sanding. Even if it's a little thick on the inside, it shouldn't make them uncomfortable too much.

But I'm not a woman so I can't say for sure. ;)

Thats the same thing that I did, bro. I just used epoxy putty because it dries to be solid as a rock in like 5-7 minutes. Its a lot harder than Bondo.
 
Or you could fill the epoxy on the back b4 sanding there for you would be able to sand it down to the level you wanted an b done with it
 
I could have... But I didn't think I was gonna break through. Like Muad said, it doesn't LOOK like its gonna be that difficult, but turns out that its a pain. Probably best to just get one that doesn't have nips at all. Just save the headache all together. Stupid nipples... lol...
 
This thread is more than 13 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top