Subscribe
  1. Morphen Jar's Avatar
    Member Since
    Jan 2007
    Posts
    28
    Jan 8, 2007, 11:42 PM - Vacuum Forming #1

    How do you make the molds and make a Vacuuform machine
  2. VashDstampede's Avatar
    Member Since
    Dec 2002
    Posts
    672
    Jan 8, 2007, 11:53 PM - Re: Vacuum Forming #2

    OK, I've seen you ask these in a few threads and I'm glad you finally asked in the right one
    Everything you need to know about the basics of these are listed below.

    Here's a good site here:
    http://www.studiocreations.com/howto...per/index.html
    And another here:
    http://www.tk560.com/vactable4.html

    The book The Prop Builder's Molding & Casting Handbook is also a good guide for making a vac-table and other questions you may have.

    Cheers,
    Ely
  3. Member Since
    Nov 2006
    Posts
    51
    Jan 9, 2007, 8:10 PM - Re: Vacuum Forming #3

    Quote Morphen Jar said: View Post
    How do you make the molds and make a Vacuuform machine
    Here's a draft chapter on how to make a vacuum forming machine that uses a kitchen oven and a vacuum cleaner, which I posted on the aforementioned tk560.com.

    http://www.tk560.com/phpBB2/viewtopic.php?t=466

    Sorry, there aren't a lot of photos yet, but there's lots of info, including

    * how to find a good vacuum cleaner for vacuum forming dirt cheap (shop vacs are overrated; you can get just as good a vacuum for a few dollars at a thrift store if you know what to look for)

    * how to make a board with a hole in it work as several sizes of platen, with removable gaskets on tape-down sheets (and why that's as good a platen as you can have if you're making one object at a time)

    * several ways to make plastic-holding frames, including mix-and-match-size frames using windowscreen framing material from the hardware store

    If you're interested in making a smallish (12 x 20) standalone oven for your vacuum former, very inexpensively you might check out this mini-howto I posted over at rcgroups.com:

    http://www.rcgroups.com/forums/showthread.php?t=621858

    (If you want to make a slightly more expensive oven that sits over your platen, look in that thread for the link & other info about Ralis Kahn's plans on halloweenfear.com)

    If you want to make a big vacuum former with it's own oven, e.g. 2 x 2 feet or bigger, check out the Thurston James design over at tk560.com, including Jim Egner's cost-saving substitutions.

    The vacuum forming forum on the discussion board there is very useful and friendly. There's also good info on the vacuum forming forums at hobbymolding.com (but that one's less active) and the one at CNCzone.com (where there are experienced pros as well as hobbyists and noobs).

    http://www.tk560.com/phpBB2/viewforum.php?f=1
    http://www.hobbymolding.com
    http://www.cnczone.com/forums/forumdisplay.php?f=291

    As for making molds, start with this recent thread here:

    http://www.thedentedhelmet.com/showthread.php?t=16584

    You might check out the "similar threads" listed at the bottom of that page.

    I'd recommend getting Thurston James's book "The Prop Builder's Molding and Casting Handbook." (You can probably find it in your local library, or get them to interlibrary borrow it for you.) The chapter on vacuum forming in that book is short, but many of the other techniques in the book can be used for making molds for vacuum forming. (It's also got the vacuum former plans that a lot of tk560 folks have used.)

    Paul
  4. Member Since
    Apr 2006
    Posts
    1,094
    Jan 9, 2007, 8:28 PM - Re: Vacuum Forming #4

    I would have to say the most important thing is to wait until you KNOW you can do it. You have to know how much sag to look for in the sheet of plastic, the last thing you want is moltent plastic ripping and getting all over the inside of your oven.
  5. Member Since
    Nov 2006
    Posts
    51
    Jan 10, 2007, 9:41 AM - Re: Vacuum Forming #5

    Quote zombierepellent said: View Post
    I would have to say the most important thing is to wait until you KNOW you can do it. You have to know how much sag to look for in the sheet of plastic, the last thing you want is moltent plastic ripping and getting all over the inside of your oven.
    Two ways to avoid this:

    1. (a) Put a piece of aluminum windowscreen across the bottom of the oven, propped up on something (maybe the bottom rack). If you have a meltdown, the plastic will hit the screening first, not the bottom element, etc. This should give you time to whip it out of the oven before it makes a bigger mess.

    (b) Be careful. Start with the oven at a lower heat than you think you need, and see if it's hot enough. Like 200. Bump up the heat 50 degrees at a time, waiting a couple of minutes in between, until the plastic starts to sag. That'll give you a handle on how hot to set your oven so that things don't happen too fast.

    2. Build a standalone oven from cheap/disposable stuff, and put window screening across the bottom of that, too.
  6. SDmicp's Avatar
    Member Since
    Aug 2012
    Posts
    12
    Aug 12, 2012, 12:24 AM - Re: Vacuum Forming #6

    Glad I found this thread. Its exactly what I was looking for!

Similar Threads

  1. Mini vacuum forming help
    By SUPERprops in forum The Sarlacc Pit
    Replies: 20
    Last Post: Feb 17, 2010, 10:08 PM
  2. vacuum forming alternatives
    By slimguy379 in forum The Sarlacc Pit
    Replies: 2
    Last Post: Nov 1, 2008, 11:25 PM
  3. Vacuum Forming Table
    By CombatBaby in forum Prop Building Workshop
    Replies: 5
    Last Post: Oct 30, 2008, 2:41 AM
  4. vacuum forming
    By Gandhi in forum Prop Building Workshop
    Replies: 11
    Last Post: Nov 8, 2005, 12:45 PM
  5. Vacuum Forming
    By Bobo in forum Prop Building Workshop
    Replies: 11
    Last Post: Apr 18, 2003, 11:54 PM