Subscribe
  1. Christo Fett's Avatar
    Member Since
    May 2005
    Posts
    250
    Jul 3, 2005, 1:28 PM - Paint Bubbling : WHY?!?!?! #1

    Well my FG bucket is almost ready for paint and I hit it with some primer and the primer is bubbling up. The texture looks almost like tree bark. I sanded it down cleaned the helmet with rubbing alcohol hit it again with some primer and it did the same thing. Can anyone tell me why and if there is something that I can clean my helmet with so this won't happen?
  2. judz dwedd's Avatar
    Member Since
    Mar 2002
    Posts
    1,529
    Jul 3, 2005, 1:36 PM - Re: Paint Bubbling : WHY?!?!?! #2

    If it's a gelcoated helmet, try washing it down with acetone. Some people, (most probably) cast helmets from a silicone mold. Silicone molds tend to leave a silicone oil residue on parts cast from them. Also, polyester based resins have a sticky surface when cast from silicone molds. This also is removed with the acetone.

    If it's a urethane resin helmet, DO NOT use acetone on it. Acetone will damage urethane resin.
  3. Member Since
    Jul 2005
    Posts
    590
    Jul 3, 2005, 1:41 PM - Re: Paint Bubbling : WHY?!?!?! #3

    Possibly bad can of primer?

    I havn't painted a helmet yet but have built models for many years. It's possible some of the release agent used to get it out of the mold might still be on the helmet.
    I have used comet cleanser and an old toothbrush in warm water to remove this stuff from resin parts. Have heard wesly's bleach white used on white wall tires works well too. Not sure what it would do to the fiberglass. I would recomend if you try it to test it first.
    The comet shouldn't have any effect on the FG.


    Just my 2 cents.
    Hope it helps.

  4. Christo Fett's Avatar
    Member Since
    May 2005
    Posts
    250
    Jul 3, 2005, 2:37 PM - Re: Paint Bubbling : WHY?!?!?! #4

    Thanks guys!

    Acetone, can I use nail polish remover? Isn't that acetone?
  5. judz dwedd's Avatar
    Member Since
    Mar 2002
    Posts
    1,529
    Jul 3, 2005, 3:44 PM - Re: Paint Bubbling : WHY?!?!?! #5

    Nail polish remover may have acetone in it, but it has other stuff, as well. I'm not sure if nail polish remover would be a good idea. Also, ask the person you got it from if it's gelcoated or not. Acetone will not damage a gelcoated surface, but could mess up a raw fiberglass surface. If it's NOT gelcoated, use mineral spirits instead.
  6. Member Since
    Jul 2005
    Posts
    590
    Jul 3, 2005, 5:46 PM - Re: Paint Bubbling : WHY?!?!?! #6

    Speaking of mineral spirits and stuff like that.
    Don't use goof off adhesive remover on a polycarbonate t-visor. It will melt it. I just found out the hard way on that. Guess i have to buy another green face shield next week..

  7. Christo Fett's Avatar
    Member Since
    May 2005
    Posts
    250
    Jul 3, 2005, 7:50 PM - Re: Paint Bubbling : WHY?!?!?! #7

    It looks like raw fiberglass to me. I guess I'll use mineral spirits.
  8. judz dwedd's Avatar
    Member Since
    Mar 2002
    Posts
    1,529
    Jul 4, 2005, 8:14 AM - Re: Paint Bubbling : WHY?!?!?! #8

    It might also help to give it a moderate sanding with some fine sandpaper, to dull the surface and get the paint to bond better.
  9. Christo Fett's Avatar
    Member Since
    May 2005
    Posts
    250
    Jul 5, 2005, 2:59 PM - Re: Paint Bubbling : WHY?!?!?! #9

    I've sanded it with all kinds of sandpaper prior to this. I decided to try the "Comet with warm water and a toothbrush" method. I'll report back when I try to prime again.
  10. BobaN00b's Avatar
    Member Since
    Mar 2005
    Posts
    558
    Jul 7, 2005, 2:25 PM - Re: Paint Bubbling : WHY?!?!?! #10

    christo, i have had the same problem. Not with the primer though. I had the problem once I put paint on top of the chrome. I would get the bubbly, crooked lines. Of course, i was using crap spray paint and when I went out and got the good Krylon, I didn't have the problem anymore.
  11. Christo Fett's Avatar
    Member Since
    May 2005
    Posts
    250
    Jul 7, 2005, 2:56 PM - Re: Paint Bubbling : WHY?!?!?! #11

    Good news!
    I just came in from putting on a second coat of primer and it is not lifting or bubbling up at all. The problem had to be silicone residue because the bubbling was around all of the edges and crevases. It seems as though the maker just wiped down the helmet with some kind of cleanser but didn't use a brush to get into the crevases. I washed it down with Comet cleanser like Jun Garros Fett had suggested because this seemed like the safest of all of the chemicals that were recommended and it worked great.
  12. judz dwedd's Avatar
    Member Since
    Mar 2002
    Posts
    1,529
    Jul 7, 2005, 5:41 PM - Re: Paint Bubbling : WHY?!?!?! #12

    I'm glad you got it squared away.
  13. Admin Staff webchief's Avatar
    Member Since
    Mar 2002
    Posts
    4,703
    Jul 7, 2005, 10:46 PM - Re: Paint Bubbling : WHY?!?!?! #13

    Excellent news. Glad it worked out for you!
  14. Member Since
    Jul 2005
    Posts
    590
    Jul 7, 2005, 11:44 PM - Re: Paint Bubbling : WHY?!?!?! #14

    Glad it worked. Good luck on the rest of the painting.



Similar Threads

  1. Fettpride Helmet ESB paint job...NEW PAINT PICS!
    By godaking in forum Boba Fett Helmet
    Replies: 14
    Last Post: Jun 23, 2009, 11:25 AM
  2. I Need Some Paint Help
    By shortimer52 in forum Prop Building Workshop
    Replies: 11
    Last Post: Mar 20, 2009, 9:58 AM
  3. need to paint DPM
    By Ronin677 in forum Prop Building Workshop
    Replies: 4
    Last Post: Jul 24, 2008, 7:57 AM
  4. Where's the paint!
    By texasfett in forum Boba Fett Helmet
    Replies: 6
    Last Post: Mar 6, 2006, 9:27 PM
  5. Paint Question - Possibly DUMB paint question!
    By Ego in forum Prop Building Workshop
    Replies: 9
    Last Post: Jan 15, 2003, 9:04 PM