Results 1 to 6 of 6

Hot Blued ROTJ Flamethrower Nozzles

Discussion on Hot Blued ROTJ Flamethrower Nozzles within the The Cargo Hold forum, part of the Classifieds category; I have a PAIR of hot-blued ROTJ left gauntlet flamethrower

  1. #1
    Fettered's Avatar
    Join Date
    Jul 2011
    Location
    Eastern PA
    Age
    37
    Posts
    297

    Hot Blued ROTJ Flamethrower Nozzles

    I have a PAIR of hot-blued ROTJ left gauntlet flamethrower nozzles. They are 1" long and 1/2" diameter. I am asking $15 (Paypal) shipped in US. Thanks!

    Nozzles you will get:
    p1210789.jpg

    Before and After bluing:
    p1210788.jpg

    For comparison, here is the original prop via AOSW.

  2. #2
    Fettered's Avatar
    Join Date
    Jul 2011
    Location
    Eastern PA
    Age
    37
    Posts
    297

    Re: Hot Blued ROTJ Flamethrower Nozzles

    bump.

  3. #3
    Darth Voorhees's Avatar
    Join Date
    Dec 2007
    Location
    Brooklyn/NYC
    Age
    41
    Posts
    2,053

    Re: Hot Blued ROTJ Flamethrower Nozzles

    Those are nice! If i had a ROTJ Fett, id be all over them! lol

    Free bump for a great guy to deal with!

  4. #4
    Fettered's Avatar
    Join Date
    Jul 2011
    Location
    Eastern PA
    Age
    37
    Posts
    297

    Re: Hot Blued ROTJ Flamethrower Nozzles

    Thanks Lou

  5. #5
    JodoKast89's Avatar
    Join Date
    Sep 2011
    Posts
    139

    Hot Blued ROTJ Flamethrower Nozzles

    Will SE need these? And will they fit FP gauntlets?

  6. #6
    Fettered's Avatar
    Join Date
    Jul 2011
    Location
    Eastern PA
    Age
    37
    Posts
    297

    Re: Hot Blued ROTJ Flamethrower Nozzles

    They work for SE as well as ROTJ.

    I don't own FP gauntlets, but based on photographic measurements of the flame thrower housing on his site versus the calc pad I believe they would look good in a FP gauntlet, but for any gauntlet you will need to find a way to attach them. I have a pair on 3/8" tubing, but I needed to turn the tubing down to fit; 3/8 was a bit too big.

    If you have the resin part supplied by Fett Pride you may be able to work off of that block, but again, I don't own them so I can't say for certain. As indicated in the photo they are 1/2" in diameter at the knurl, so you might be able to compare to the FP resin bit if you already have them.

Similar Threads

  1. Question: FP ROTJ Gauntlet flamethrower..
    By Escher in forum Boba Fett Armor
    Replies: 5
    Last Post: 11-28-2010, 03:47 PM
  2. RotJ Flamethrower nozzles
    By BobaFettish in forum Boba Fett Armor
    Replies: 24
    Last Post: 06-11-2003, 10:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21