Rub N Buff Jango H E L P !!!!!

rasman06

New Hunter
My first time.

Sanded with 400 dry
Primed with Rustoleum 2x. Waited 30 hrs
Wet sanded with 1,000 - waited 12 hrs

Used my hands with rub n buff silver leaf
ImageUploadedByTapatalk1431301800.738630.jpg

My armor looks like this. Is that how it is supposed to look. I see some swirl marks. Did I use to much? Not enough? Can I recoat?

The tube had a 2014 date on it. Just ordered last week.

ImageUploadedByTapatalk1431301912.736007.jpgImageUploadedByTapatalk1431301925.088657.jpgImageUploadedByTapatalk1431301934.806189.jpg

Any advice please.




Sent from my iPhone
 
Looks great on my IPhone, but that may not help. Swirls in it like too much put down? Like build up? Maybe take it off and try again using less? It is ok though if it's not completely smooth like mirrored finish. It will still need some weathering, and it should look used. I've only done small parts with R and B, so not sure when covering a large surface area.
 
Looks great on my IPhone, but that may not help. Swirls in it like too much put down? Like build up? Maybe take it off and try again using less? It is ok though if it's not completely smooth like mirrored finish. It will still need some weathering, and it should look used. I've only done small parts with R and B, so not sure when covering a large surface area.

How do they recommend weathering over rub n buff on gel coated?


Sent from my iPhone
 
Acrylics, watered down work great. They're cheap, and water based so you can wipe it off if you go too heavy. Best to start light, and get black and burnt umber colors. Damp cloth and work in a little acrylic paint. Blot it on and blot it down to tame it. Most focus is on the edges to represent oxidation and pinging from working the metal look.
 
Take a look at this video for many of your questions. The guy who made this knows a bit about Jango Fett.

 
Last edited by a moderator:
Take a look at this video for many of your questions. The guy who made this knows a bit about Jango Fett.


Thanks Mullreel - I've watched that Cruzer vid a million times. He makes it look so simple.


Sent from my iPhone
 
Last edited by a moderator:
You will get some swirls no matter what you do. You can try buffing with a very soft cloth like an old t shirt after a few days of the rub n buff drying and that will help. You can also wet sand the rub n buff after it dries and try again and I found you get a better finish the second time. I think the rub n buff fills in some of the small pores and gives a better base to work on.

For weathering I usually use use acrylics and a very wet sponge and sponge it on and wipe off if I get to much on at first.
 
You will get some swirls no matter what you do. You can try buffing with a very soft cloth like an old t shirt after a few days of the rub n buff drying and that will help. You can also wet sand the rub n buff after it dries and try again and I found you get a better finish the second time. I think the rub n buff fills in some of the small pores and gives a better base to work on.

For weathering I usually use use acrylics and a very wet sponge and sponge it on and wipe off if I get to much on at first.

Thanks ~ do you wet sand and use 800 - 1,000 I assume?


Sent from my iPad
 
I had the same problem at first with rub and buff. When I first did it I put it directly on the piece and it lumped up. The second time I put it on my hands then rubbed it into the armor and it worked perfectly.
 
This thread is more than 8 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top