Rangefinder size comparisons

Jc27

Well-Known Hunter
Preferred Vendor
TDH PREMIUM MEMBER
I was wondering a few things about the rangefinder. I am in the process of making a light kit and was curious about the most popular models of the RF. I know Asok sells them with his CC helms(which are awesome by the way), and terminal fettler makes them ,as well as the don post pieces are the ones I read about he most.
My question is mainly about the size difference between them all. My kit was build to fit Asok's lid and I am wondering how much I will have to alter the design to get it to fit in the other RFs if I decide to make them.
Thanks,
JC
 
I have a TF rangefinder kit on the way. If nobody else provides measurements
before it gets here, I'll be glad to provide them once I receive it.
 
Hi JC,
I got my Terminalfettler RF, and I took a couple of measurements.
These are measurements of the space inside the RF:
Width (front to back): 30 mm
Height: 18 mm

Keep in mind, those are the absolute limits of the space available
inside the RF. If a board was built to those dimensions, it would be
a very tight scrape getting it in there.
Hope that helps!
 
Thanks that will help. If you could take a pic of the inside that would be awesome. I need to check my circuit to see the dimensions but it should fit.
 
Heres a comparison between the TF Topper and a RS Props Topper which is similar to ASOK's size. I can't stress how nice the TF's toppers are. I've had them all in hand at one time or another but the TF really stuck out as the most accurate of them all in my honest opinion and his block and lens are very clear and clean. Sorry I wondered off topic there. But I hope these comparison pictures help you out.

2013-03-26_00-03-57_388.jpg
2013-03-26_00-03-33_287.jpg
2013-03-26_00-05-19_994.jpg
2013-03-26_00-05-31_142.jpg

if you need a better pic or something specific just lemme know
 
Last edited by a moderator:
Heres a comparison between the TF Topper and a RS Props Topper which is similar to ASOK's size. I can't stress how nice the TF's toppers are. I've had them all in hand at one time or another but the TF really stuck out as the most accurate of them all in my honest opinion and his block and lens are very clear and clean. Sorry I wondered off topic there.

I agree! It's hard to beat terminal fettler's awesome rangefinders! I have the viewfinder and the perspex block from him and I can't praise enough the excellent craftsmanship and care for details!
 
How much does he sell them for and what is the wait time for one?
 
Hi, excuse me for butting in. My RF tops are £40 (GBP) shipped. I have a batch ready to ship, 5-7 days delivery time to your door. Also, because the lens Perspex section is hand cut and finished, I can supply this part to you specification to fit another housing. Please feel free to PM me, or ask any questions here...(y)
 
Hi, excuse me for butting in. My RF tops are £40 (GBP) shipped. I have a batch ready to ship, 5-7 days delivery time to your door. Also, because the lens Perspex section is hand cut and finished, I can supply this part to you specification to fit another housing. Please feel free to PM me, or ask any questions here...(y)

do you ship to the US? and if so, what's the cost in US Dollars?
 
This thread is more than 10 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top