Subscribe
  1. Oct 7, 2008, 12:43 PM - MQ-1 board #1

    i just got my new helmet that i bought from a fellow TDH member comes with a MQ-1 for the back now my issue is i got a big head and the board hurt the back of my head with the helmet on.....i took out the board and it fits great...i like the MQ-1 board in and wish to put it back there looks like there is room to sand down the buldge where the vents is.. has anyone ever done this and will it cause any defects to the helmet...or has anyone eles had this problem and how? ill be thankfull for any and all advice that will help
  2. Stormrider's Avatar
    Member Since
    Aug 2007
    Posts
    2,262
    Oct 7, 2008, 1:00 PM - Re: MQ-1 board #2

    I have rubber MQ boards that go with my helmet interior kits v3. Might be an option.
  3. Oct 7, 2008, 1:07 PM - Re: MQ-1 board #3

    sounds like it could help can i get a pic and a price
  4. stormtrooperguy's Avatar
    Member Since
    Dec 2004
    Posts
    5,039
    Oct 7, 2008, 1:48 PM - Re: MQ-1 board #4

    i've been able to file out some of the inside of the keyslots... it really depends on how thick the resin/fiberglass is. you can also round the back of the mq-1 slightly.

    the rubber one sounds like a great idea though.
  5. Oct 7, 2008, 11:55 PM - Re: MQ-1 board #5

    well it is a mystery helmet from what i am told and seems to be think enough to file down i just do wanna risk messing it up
  6. Murphoid's Avatar
    Member Since
    Dec 2007
    Posts
    341
    Oct 10, 2008, 10:10 AM - Re: MQ-1 board #6

    I'm doing the same thing with my MH, not because its too small with the MQ-1 board in, but because of the lack of visible detail on the board with the thick keyslots. I've sanded them down quite a bit, and no defects yet. Just take it a little bit at a time.
  7. formerly old_jedi_mind_trick Bobby Fett UK's Avatar
    Member Since
    Nov 2007
    Posts
    1,453
    Oct 10, 2008, 3:23 PM - Re: MQ-1 board #7

    Can't you make your head smaller?

    Good luck with it buddy!
  8. Stormrider's Avatar
    Member Since
    Aug 2007
    Posts
    2,262
    Oct 10, 2008, 4:16 PM - Re: MQ-1 board #8

    Dont 'file it down'
    Take a 'foam sandpaper block' and 'sand it down' it will go slow so you wont destroy it or slip. Just rub it up and down.
  9. Oct 11, 2008, 5:56 PM - Re: MQ-1 board #9

    well gona see about the rubber mq-1 first to try and save the helmet from any mishaps if not ill try the sand down thanks for the tips

Similar Threads

  1. Servo Board
    By Darth-Jay in forum Boba Fett Helmet
    Replies: 4
    Last Post: Oct 9, 2007, 12:31 AM
  2. MDF or particle board
    By Southern hunter in forum Boba Fett Helmet
    Replies: 6
    Last Post: Feb 13, 2007, 8:15 AM
  3. Board Names
    By TeamFett in forum The Sarlacc Pit
    Replies: 116
    Last Post: Nov 28, 2006, 7:30 PM