Page 1 of 3 123 LastLast

Interest thread: Cold Cast/ Carbon hollow stalk

  1. #1

    Interest thread: Cold Cast/ Carbon hollow stalk

    Hello all, i've been experimenting with my hollow stalks and have found a carbon hollow tube that will take two wires inside. This tube is stiff and much stronger than the alu. tubes i've preveously been using. The tube runs down to an internally threaded sleeve which has a hollow bolt to hold everything in place, allowing the wires to enter inside the helmet. The cold cast stalk can be buffed/polished to a fairly bright alu. finish. Please post here if interested and i'll start a list below. These will cost 18.50/$37.00 shipped. Cheers, TF...

    1. Mandalorfett/paid/shipped
    2. thedustroom
    3. Predatormv/paid/shipped
    4. digifett/paid/shipped
    5. deadbolt/paid/shipped
    6. psberetta/paid/shipped
    7. bunicula/paid/shipped
    8. matrix/paid/shipped
    9. Citizen_ snips
    10. Halo_1/paid/shipped
    11. Darthmiller
    12. Shaggy13
    13. Slave R5/paid/shipped
    14. HMPOTC33
    15.TK 4130/paid/shipped
    16. napalm/paid/shipped
    Paypal address is garrett.kate@btinternet.com these should be ready to ship in the next 10-14 days, i'll keep you posted, thanks, TF...
    LIST UPDATED. These will ship this week, Thanks.
    Attached Thumbnails Attached Thumbnails dscf0008-jpg   dscf0009-jpg  
    Last edited by terminal fettler; Aug 2, 2007 at 1:38 PM. Reason: update

  2. #2
    I helped at SDCC '08 MandalorFett's Avatar
    Member Since
    Nov 2005
    From
    California USA
    Posts
    2,738

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Interested.



  3. #3
    Jango's kid's Avatar
    Member Since
    Nov 2002
    From
    SW Minnesota, very small town
    Posts
    2,517

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    WOW!!!! Those look pretty dang kewl!!!!! Great job!!!
    D

  4. #4
    digifett's Avatar
    Member Since
    May 2007
    From
    Germany, Near Frankfurt
    Posts
    71

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Those look absolutely great ! What are the measurements ??

  5. #5

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    hi, measurements are: centre of pivot to underside of RF: 160mm, tab into RF: 9mm, pivot diameter: 10.5mm, stalk width: 9.5mm, stalk thickness: 6.5mm, width of top when in RF: 34mm...

  6. #6
    digifett's Avatar
    Member Since
    May 2007
    From
    Germany, Near Frankfurt
    Posts
    71

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Thanks a lot fettler !! Those measurements are almost perfect to fit my helmet, too. But it sounds like your stalk has overall the same stalk width, or is your stalk tapered? I am pretty new here so I am not a Boba Fett pro !! But I read this thread here: http://www.thedentedhelmet.com/showt...ighlight=stalk

  7. #7
    thedustroom's Avatar
    Member Since
    Nov 2006
    From
    High Peak, England
    Posts
    134

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Interested!

  8. #8
    Predatormv's Avatar
    Member Since
    Nov 2002
    From
    Orlando, FL
    Posts
    2,199

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Yea I am interested in 1 maybe 2.

  9. #9

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    digifett said: View Post
    Thanks a lot fettler !! Those measurements are almost perfect to fit my helmet, too. But it sounds like your stalk has overall the same stalk width, or is your stalk tapered? I am pretty new here so I am not a Boba Fett pro !! But I read this thread here: http://www.thedentedhelmet.com/showt...ighlight=stalk
    There's no taper on my stalk...

  10. #10
    digifett's Avatar
    Member Since
    May 2007
    From
    Germany, Near Frankfurt
    Posts
    71

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Your stalk is so good, I would like one, too!

  11. #11

    Member Since
    Apr 2006
    From
    Whitehorse, Yukon
    Posts
    1,094

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Guys you really want to jump on these asap. TF has the neatest and most organized set up for a range finder stalk that I've ever seen.

  12. #12
    deadbolt's Avatar
    Member Since
    Feb 2006
    From
    Virginia
    Posts
    507

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    I'm in!

  13. #13
    psberetta's Avatar
    Member Since
    Mar 2005
    From
    Iowa
    Posts
    751

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    I'm in for one TF.

    Hey guys, to convert mm into inches all you need to do is divide the mm by 25.4

    EX : 160 mm / 25.4 = 6.2992 inches



    -Tim-

  14. #14
    bunicula's Avatar
    Member Since
    Dec 2006
    From
    Athens, GA
    Posts
    151

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    i'm interested in 2 if it's possible. thanks

  15. #15
    Matrix's Avatar
    Member Since
    Feb 2006
    From
    Canada
    Posts
    78

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Nice work! Definately interested!

  16. #16

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    i'm in! thanks

  17. #17
    Halo_1's Avatar
    Member Since
    Oct 2002
    From
    East Coast, Singapore
    Posts
    1,437

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    TF,

    I'm in...Gracias.

    Tim.

  18. #18
    I helped at SDCC '08 GCNgamer128's Avatar
    Member Since
    Jan 2006
    From
    Las Vegas, Nevada USA
    Posts
    5,520

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    I may be interested, but I won't be happy to have to modify my BM bucket for it to fit.

  19. #19
    Mojo-Fett's Avatar
    Member Since
    May 2007
    From
    UK
    Posts
    4,783

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Hey G...I'll take one with the new lid...
    Those look totally wicked... great job.

    -Gavin-

  20. #20
    DarthMiller's Avatar
    Member Since
    Jun 2005
    From
    Ft. Worth, TX
    Posts
    1,193

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    count me in

  21. #21
    I helped at SDCC '08 NovallTalon's Avatar
    Member Since
    Feb 2007
    From
    Yadkinville NC
    Posts
    2,028

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    I may be interested to, with the same concern as GCNgamer128.

  22. #22

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    Interested!

  23. #23
    SlaveR5's Avatar
    Member Since
    Nov 2005
    From
    Irvine, CA
    Posts
    354

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    is there still room on the list? if so put me down for one as well.

    thanks!

  24. #24

    Member Since
    Jan 2007
    From
    Vacaville, California
    Posts
    361

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    TF,
    Is it to late to pay pal and get on the list. I love your aluminum old version and this appears to be the upgrade for it. Thanks,
    Ron

  25. #25
    SlaveR5's Avatar
    Member Since
    Nov 2005
    From
    Irvine, CA
    Posts
    354

    Re: Interest thread: Cold Cast/ Carbon hollow stalk

    payla sent.
    thanks!
    Craig

Similar Threads

  1. cold cast alu stalk with bubbles?
    By terminal fettler in forum Prop Building Workshop
    Replies: 11
    Last Post: Mar 26, 2006, 10:15 AM
  2. HOLLOW STALK : small run interest
    By bobamaker in forum Boba Fett Helmet
    Replies: 8
    Last Post: Mar 2, 2006, 12:28 AM
  3. Hollow metal RF stalk
    By Delta13 in forum Boba Fett Helmet
    Replies: 9
    Last Post: Nov 28, 2002, 1:02 PM
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •