Subscribe
  1. Bobo's Avatar
    Member Since
    Apr 2003
    Posts
    650
    Apr 26, 2006, 10:00 PM - Bondo Glazing Putty #1

    Hey guys!

    Just gettin ready to clean my MS up and I'm about to fill and sand the small air bubbles and imperfections. I don't need alot of bondo so the can is probably going to get wasted, so I'm curious if the Bondo Glazing Putty in the squeeze tube will work?

    cheers,
    Bartek
  2. fettpride's Avatar
    Member Since
    Mar 2002
    Posts
    2,654
    Apr 26, 2006, 10:04 PM - Re: Bondo Glazing Putty #2

    Quote Bobo said:
    Hey guys!

    Just gettin ready to clean my MS up and I'm about to fill and sand the small air bubbles and imperfections. I don't need alot of bondo so the can is probably going to get wasted, so I'm curious if the Bondo Glazing Putty in the squeeze tube will work?

    cheers,
    Bartek

    Only for "ULTRA" fine scratches or scuffs. Don't bother filling ANYTHING that is deeper than that with this stuff. That's all galzing is ... very fine filling. If you take the chance on filling anyhting really deep with it, you will have to do it in layers, making sure it dries fully (air at room temp) before adding the next, ect. ect.

    If you're concerned about wasting, just go get a single can of Bondo "Ultimate". It's blue when mixed. 9.5 oz. Better than the run of the mill pink bondo, easier to sand, feathers better. Sticks to ANYTHING ! Only about 12 bucks at Wal-Mart.





    FP
  3. I helped at SDCC '08 Jango 5204's Avatar
    Member Since
    Nov 2005
    Posts
    1,376
    Apr 26, 2006, 10:18 PM - Re: Bondo Glazing Putty #3

    I use a thin glazing puddy made by evercoat. It's made to be put on thin and blocked flat in automotive applications. I don't see why you can't use regular bondo, if you already have it. Use a plastic spreader and don't put on more than you need, squeeze it into your holes as you wipe over it. The glazing putty is thin and likes to self level itself, which makes it hard to do things on the side of an object, it sometimes runs out.

    good luck.
  4. Bobo's Avatar
    Member Since
    Apr 2003
    Posts
    650
    Apr 26, 2006, 10:44 PM - Re: Bondo Glazing Putty #4

    Thx FP!

    I just didn't want to buy a can of bondo that I'll only use a teaspoon of, that's all. Guess I have no choice!

    B
  5. MARROW SUN's Avatar
    Member Since
    May 2004
    Posts
    608
    Apr 26, 2006, 10:47 PM - Re: Bondo Glazing Putty #5

    You can also try CA glue or superglue for the small bubbles
  6. Apr 26, 2006, 10:59 PM - Re: Bondo Glazing Putty #6

    I use superglue. it works well.
  7. fettpride's Avatar
    Member Since
    Mar 2002
    Posts
    2,654
    Apr 26, 2006, 11:06 PM - Re: Bondo Glazing Putty #7

    Quote MARROW SUN said:
    You can also try CA glue or superglue for the small bubbles






    Actually, lets take that a little bit further ...


    Superglue and BAKING SODA. Good 'ol Arm & Hammer

    I didn't even think to offfer that info, as I had in mind more of the "finishing/Feathering" properties of filler. But yes, it's and awesome way to go if your in a pinch. I've been doing it for years

    The baking soda acts as an instant filler for larger areas. Drop super glue in first, sprinkle the baking soda over the top of it ... dries instantly. Use it in layers if you need to for biiger gaps. Hard as steel. The only downsize is that it's a little harder to sand if you in the "Finishing/Feather" stages. But you could use this method to fill your gaps, and then use glazing putty over the top to smooth it out.





    Quote Bobo said:
    Thx FP!

    I just didn't want to buy a can of bondo that I'll only use a teaspoon of, that's all. Guess I have no choice!

    B

    Oh, and uh Bobo ... if your into "Fett", don't worry about a small can of Bondo bud ... you're gonna need it

    Just pound the lid back on it, and call it good. It last's forever sealed.




    FP
    Last edited by fettpride; Apr 26, 2006 at 11:12 PM.
  8. Member Since
    Nov 2003
    Posts
    458
    Apr 26, 2006, 11:38 PM - Re: Bondo Glazing Putty #8

    Quote fettpride said:




    Just pound the lid back on it, and call it good. It last's forever sealed.




    FP
    Or even for 4 month's unsealed (with the lid slightly cocked) as I recently found out

    Loranar
  9. fettpride's Avatar
    Member Since
    Mar 2002
    Posts
    2,654
    Apr 26, 2006, 11:42 PM - Re: Bondo Glazing Putty #9

    Quote Loranar_Fett said:
    Or even for 4 month's unsealed (with the lid slightly cocked) as I recently found out

    Loranar







    Yep, been there too ... even if it's a little dried out, just mix a tad of acetone in it



    FP
  10. Nachtinis's Avatar
    Member Since
    Apr 2006
    Posts
    175
    Apr 27, 2006, 6:08 PM - Re: Bondo Glazing Putty #10

    You might also want to try joint compound. I use it. You can spread it with your fingers and clean up with water. It air drys and sands quickly. Since its basically a paper, it will also seal with most paints/sealers/urethanes/glazes, etc...
  11. yanvaq's Avatar
    Member Since
    Jan 2006
    Posts
    21
    Apr 28, 2006, 9:41 PM - Re: Bondo Glazing Putty #11

    Just buy the can of bondo after you have it you might be supprised what you will find to do with it. also I use the bondo spot puty all the time and love that stuff just has a high shrink factor so have to layer deeper holes but dries reel fast
  12. formerly joNich
    Member Since
    Dec 2005
    Posts
    589
    Apr 29, 2006, 7:32 AM - Re: Bondo Glazing Putty #12

    I goes great on chili fries!





    just kidding...
  13. Spideyfett is offline Spideyfett
    Apr 29, 2006, 9:10 AM - Re: Bondo Glazing Putty #13

    WOW..some great Tips on this Thread...Thanks GUYS!!
  14. psberetta's Avatar
    Member Since
    Mar 2005
    Posts
    751
    Apr 29, 2006, 9:29 AM - Re: Bondo Glazing Putty #14

    This one may sound weird..........it also involves superglue.

    Some of you might know this one but, I love this little mix. Take some "babypowder" sprinkle it out onto a piece of SCRAP plastic...
    NOT paper (soaks up the superglue) and make a volcano shape out
    of it. Next just drop some superglue into your volcano and mix it up .
    The more babypowder you add, the thicker it will get. It dries fast and hard, and sands VERY nice. Once you try it a few times you'll get the hang of it. Its easy to add more babypowder than glue so keep that tip in mind. Hope you all like it..................Instant filler
    -Tim-
  15. deadbolt's Avatar
    Member Since
    Feb 2006
    Posts
    507
    Apr 29, 2006, 11:51 AM - Re: Bondo Glazing Putty #15

    It's amazing what you can do with super glue, it's like the next duct tape
    Awsome techniques guys!
    Last edited by deadbolt; Aug 11, 2011 at 9:54 PM.

Similar Threads

  1. MMD Green Putty?
    By Southern hunter in forum Boba Fett Helmet
    Replies: 2
    Last Post: Mar 22, 2008, 5:18 PM
  2. Helmet Build Up - Clay / Putty?
    By Stormrider in forum Prop Building Workshop
    Replies: 1
    Last Post: Oct 30, 2007, 1:19 PM
  3. epoxy putty removal?
    By TantiveIV in forum Prop Building Workshop
    Replies: 4
    Last Post: May 19, 2007, 12:33 AM
  4. Bondo.
    By slacker in forum Prop Building Workshop
    Replies: 12
    Last Post: Feb 27, 2007, 9:01 PM
  5. Mixing Fiberglass Resin & Filler Putty
    By Migrate from As You Wish in forum Prop Building Workshop
    Replies: 7
    Last Post: Apr 6, 2002, 7:42 PM