New Member Darklord Tries to Build a Better Boba Action Figure

As most of you know, my camera was down for about a month, preventing me from documenting some of my work on this figure.

I was therefore unable to document some progress steps that occurred during the camera’s repair time.

Since those updates on the figure will be evident in the photos that I’m about to post anyway, I will list what those updates were.

1) The rangefinder on Boba’s helmet was shortened by about 2½ scale inches.
2) The cheek stripes on the helmet were re-painted in the correct flat black.
3) The T-visor on the helmet was re-painted in a darker shade of red. (Note: this T-visor re-paint was something that I was originally NOT planning to do . But admittedly I did change my mind about the desirability of the “toyetic” bright red after I saw it contrasted against the new flat black cheek stripes.
4 The minor paint rubs on the utility belt have all been touched up.
5 The armored shoulder bell for Boba’s left shoulder has been re-painted in the correct canary yellow. Knee pads and right armored shoulder bell have been left orange yellow.




Alright… onto to yesterday’s work…

A couple of months back when I performed the operation to change the profile of the figure’s helmet, I did a lot of filling work with plastic shavings to fill the gaps between the two helmet halves.

There was still a seam visible from the operation that I wanted to make disappear.

Helmetseam.jpg




I began by using a line of Krazy Glue. I laid down a sealant directly on the seam, and waited for the glue to dry and set.

Helmetglueseam.jpg


Helmetseamfilled.jpg




Once the glue dried and hardened, I sanded the seam smooth with 500 grit sandpaper, and then I did a fine wet-sanding with 1000 grit sandpaper to make the dome as smooth as possible.

Helmetseamsanded.jpg


I will air-brush the dome tomorrow, once and for all, effectively making the seam vanish.



Undoutedly, the most time-consuming operation I performed yesterday was converting the Imperial Scanning Trooper’s arm sleeves into Boba Fett’s correct double sleeve (sans arm mini pocket).

The first thing I did was to use an X-acto blade to carefully shave away the mini-pocket molded to the right arm. I gave the area a fine sanding to smooth it off, and then I got to work making the upper arm double sleeve.

shavearmpocket.jpg


sandarmpocket.jpg


smootharm.jpg



I used some sewing thread to layout the edge of the upper sleeves by carefully gluing it down around the circumfrence of both arms. Then, with my trusty razor (God, what would I do without that thing?) I re-sculpted the lower sleeve into a narrow taper that appears to emerge from underneath the upper sleeve.

thread.jpg


threadloop.jpg




threadaroundrtarm.jpg



rightarmthreaded.jpg


rightarmsculpt.jpg



finishedrightarm.jpg


finishedrightarm3.jpg


threadaroundlftarm.jpg


leftarmthreaded.jpg


leftarmsculpt.jpg


Finishedleftarm.jpg


The guide thread at the edge of each new upper sleeve is only TEMPORARY. They will be replaced by micro-thin ribbon to simulate the sleeve cuffs.



Boba’s right arm weapon gauntlet features a clear power tube that tucks underneath his right arm upper sleeve.

I used a big needle to make a hole underneath the upper sleeve ridge that I created. I then made a second hole in the coupling on the wrist weapon gauntlet. These would be the two connection points for the gauntlet’s power feed tube.

bigneedle.jpg


needletosleeve.jpg





I looked around the house for a suitable item to use as the tube. A tiny white / clear plastic binder on the bundle of new sox that I just bought was something that I thought might do the trick. In the end, I rejected it because it did not look like a tube to me, it seemed a bit small in its scale, and it did not have the flexibility I was hoping for. It kept popping out of the sleeve connection point every time I posed the figure’s elbow.


sox.jpg


soxtab.jpg


installwrongtube.jpg



I knew I was going to need a far more flexible material to resolve that issue.

A frantic search ensued in my wife’s closet, and as luck would have it, I located a brand new cashmere sweater that my wife bought for herself. The tag was still attached to the garment by a small clear rubber string! Yes!! Back in business.!!!

I cut a fragment of the string and installed it on the figure. The thicker size, the clarity, and the flexibility of the “tube” were all PERFECT!!


finaltube.jpg


finaltubecut.jpg


guantlettubeinstalled2.jpg




My next order of business was to add the straps for Boba’s armored knee pads. A reasonably straight-forward operation. I used some Plastruct strip styrene to create the straps and glued them into place behind the knees, making sure that the leg articulation was un-affected.


kneestrapmeasure.jpg


settingkneestraps.jpg


finishedkneestraps.jpg




So… a brief re-cap…

1) Helmet’s face colors have been corrected to correct shades
2) Helmet’s rangefinder has been shortened to correct height
3) Utility belt paint rubs have been repaired
4) Armored shoulder bell for left shoulder has been re-painted in correct yellow
5) Helmet seam has been filled and sanded (awaits air brushing)
6) Arm pocket has been shaved off / arm sanded smooth
7) Secondary upper sleeves have been layed-out and sculpted for both arms
8) Power tube for right weapon gauntlet has been installed
9) Rear fastening straps for armored knee pads have been installed

Custom Boba as of January 9th, 2011, 7:30 AM:

customBobaright.jpg






Coming up next: WOOKIE SCALPS

microbraids.jpg
 
Wow! This is intense devotion.....I am in awe! I would so do this if I had the patience and steady hands. I can already picture numerous trips to the hospital to sew my fingertips back on!!!!!
 
This is going to be a great one of a kind figure, but i must say, to even do this you've GOT to be the most insane person here. My ADD would have me looking fo rsomething else to do within a few hours. Kudos to you, any thought of doing runs?
 
I saw this thread today... And I was speachless on what you've done so far. So much details on a small piece... If you will correct all helmet problems with the proportion and colouring, I think that GL whould be glad to use it in any future Star Wars projects where small sized models are used. Keep up the fantastic work on this!

Respect!
 
Thanks a million for the kind words, guys!

I just wish that I could work on this figure daily and get it finished in a timely manner.

Unfortunately, my work schedule only allows me to work on it maybe once every week.

But the good news is, it shouldn't be too much longer now.:)
 
just looking at the full body pic above, and i noticed that the ear with the rangefinder attached should come down a little bit, this will make both look a bit more how it should be.
 
This is absolutely amazing!! I cannot wait to see it finished. It is really too bad we don't have more people like you working at Hasbro!

Agreed. But if they charge close to $6 a figure now, image what that would jump to if they started pumping out figrues of this quality.
 
I would pay $10-12 for one definitive Fett figure of this quality any day instead of the 5 or 6 different ones I have bought over the years at $5-7 a piece!
 
Just seeing this for the first time... all I have to say is WOW!
This is so incredible!

I would pay $10-12 for one definitive Fett figure of this quality any day instead of the 5 or 6 different ones I have bought over the years at $5-7 a piece!
I dont think I would have a problem paying around 50$ for a figure of this detail.
 
This thread is more than 9 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top