Blaster Pepakura Nemrod Holster

T

toolguy301

Guest
Designed up a version of the Nemrod holster & made 2 versions one to be 3D printed & the other to be used as a pepakura build. Knowing that there are a number of great cast version out there, but there aren't any templates out there for anyone to do a scratch build. So came up with this if someone wants to do a scratch build I thought I would share the pep file. The pep version was simplified for build purposes as can be seen in the photos.

Did the build on this to prove it out & overall this goes pretty good but the end where the barrel hole is located is a little tricky but just have to have some patience. Made the outer shell then glued pieces of .060" thick chip board on the inside. When that was completed I coated it with some Smooth Cast 320 to bind it all together & firm it up, inside & out. The tube at the top is a piece of PVC pipe. This is painted with black primer that I polished with an old sock which made it look like worn rubber. Plan on making straps for this but to this point is where it stops looking like Fett's holster.

You will need the Pepakura viewer to open the .PDO file. The viewer is free & can be downloaded here:

Pepakura Viewer

The Pulce is a cast from MLS with a 3D printed barrel.

Nemrod_Holster_Pep_Views_zps6vdxwvwy.jpg


20150711_183019_zpsfdanakde.jpg


20150711_183009_zpskbcqcrko.jpg


20150711_182941_zpsuffkiavq.jpg


20150711_182924_zps9uxtjtjp.jpg


20150711_182901_zpsvuq2oqqp.jpg


20150711_182837_zpszcmu3l8v.jpg


20150711_182814_zpsb1xkw6ij.jpg


20150711_182808_zpsrzxcya15.jpg


20150711_182747_zpslfq5tsrw.jpg


20150708_054715_zpsvgonki5c.jpg


20150708_054703_zps0nkhudgy.jpg


20150708_054656_zpsv8sja88s.jpg


20150708_054624_zpshhzygdjo.jpg


20150708_054613_zpszl8tvckk.jpg


Nemrod_Holster_Pepakura_zpsdbzzmwxq.jpg


Nemrod_Holster_Views_zpsdvhmle8e.jpg
 

Attachments

  • Nemrod_Holster_Pep_Rev_1_toolguy301.zip
    503.6 KB · Views: 617
  • Nemrod_Logo_Scale_toolguy301.pdf
    9.9 KB · Views: 655
Last edited by a moderator:
Thanks guys, hope others can make use of this.

Have also updated & added a template for the "Nemrod" logo to the first post.
 
i have a question, the front pocket in that t holster is cut or not? because on 501 data there is the front pocket instead in this great template there's not
 
The original hostler had a pocket for a knife, but they either cut if off or flattened it when they used it for the suit.
 
Here is what I did for my Jodo Kast belt.

Just took a leather strap & riveted it to the holster then made a loop which I used a Chicago screw to attach back to the holster which could be riveted as well.

Also added a leather strap with 2 rivets & a snap to go over the pistol to keep it in the holster.

http://www.thedentedhelmet.com/f34/jodo-kast-wip-51419-post663413/#post663413

http://www.thedentedhelmet.com/f34/jodo-kast-wip-51419-post666175/#post666175
wow very cool! thank you
 
Bah, how did I miss this thread? Was thinking of doing a pep build for my holster a while back but decided it would take too long especially without files and just ended up buying one. This is absolutely awesome, cheers for sharing!
 
I tried to 3d Print as you suggested, but I can't convert do anything with the PDO because it's locked? Maybe I'm reading your post wrong? Good work either way!
 
This thread is more than 2 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top