Finally installed my Heiland innards onto my ESB EE-3
http://img.photobucket.com/albums/v3...t/CIMG1626.jpg
http://img.photobucket.com/albums/v3...t/CIMG1627.jpg
Printable View
Finally installed my Heiland innards onto my ESB EE-3
http://img.photobucket.com/albums/v3...t/CIMG1626.jpg
http://img.photobucket.com/albums/v3...t/CIMG1627.jpg
That looks cool bro! I got the same end with my Heiland, but I have been thinking to use mine for a lightsaber I am working on. It does have a really good look in your blaster though!
Very nice! I don't care that it's not 100% accurate, it looks alot better with the insides showing.
I didn't know Boba carried an E-11 though :lol..........someone has TK's on the mind. jk man :D
I think I visit whitearmor.net more often than TDH as of late. Boba carries in E-11 in Battlefront II, haha, but the REAL Boba uses an EE-3 though ;)
I always debated about installing innards, but kids always shove their fingers up the barrel. I figured this might put a stop to that, and make it look better in the long run!
I purchased them from shabad about a month ago, and it took me a month how to get them in there without using a hammer and power tools, haha. Turns out, a screwdriver was all that was required :):)
Good ole Battlefront II, he will probably be carrying a Lewis gun in III.
Do you have any pics of the innards out of the gun? Just curious as to what they look like.
You can see the boring emptiness here, heh.
http://img.photobucket.com/albums/v3...t/sdccboba.jpg
Looks just like mine...except I placed mine a bit father inward on the barrel. Definately adds some realism!!!
Looks great! Do you know if he has more internals available? I have a vader saber that is hollow and needs guts:doh
I "assembled" the heiland, but with GOOP on the innards, then I took the bits that keep the innards attached off of the tube once the glue dried :)Quote:
Originally Posted by Jango's kid
Not sure, might as well send him a PM. Took me forever to find someone who had a set, been looking for about 2 years on and off.Quote:
Originally Posted by mrgr8ness
Thats exactly what I did too!!!! Then I took out the small screw that was in the center of the gutts, drilled the hole out bigger, and put a long thin bolt in there. That way i can shove it into my hyperfirm, and its perfectly centered!!! Worked well!!!Quote:
Originally Posted by GCNgamer128
Very nice. I like the look too and am doing something very similar.
So I've been noodle'in how the flash tube sits in the blaster. What's the best way to keep the tube in there. My barrel is 100% hollow the entire length. I've got a 3 cell tube (good that I don't have to cut any part of it, since the entire tube is hollow). I've got a few ideas, but am interested on what others do. What did you do Andy?
I unscrewed that black bit sticking out of the innards, then I slide the innards in the tube with the glue on the inside of the tube. Then using the holes provided on the tube, I screwed the black bit back into it, to hold the innards in place as the glue dried.Quote:
Originally Posted by Darth_Nickel
I'm not trying to be a hater, But are your knees upside down and on the wrong leg? over all you look cool yo
They are right side up, everyone else wears them up side down ;)Quote:
Originally Posted by Syper
ESB Carbonite Chamber, that check out how Boba wears his knees. This is also seen in pre-production art work, they also fit better like this. IMO, how they were meant to be worn.
Silly me:( my bad your right, Again your gear looks hella cool very detailed and you ware it well i.e. your costume fit look more like the real Boba Fett...Grats