Jet Pack harness question

Satxer

Active Hunter

• Feb 23, 2006

• #1

Jetpack harness question

Now I got my MLC verson 2 pack today and I was just having questions on how to do my hooking to the harness I wear. Now my original plan was to use these D-Clip hooks by just bolting them onto the pack. But, I did notice the 2 Rings inside the pack like they were meant to put straps on and just cut through the back of the pack to place them through...now I have the pack almost fully painted...LOL yeah already, I just need to figure out how the best way goes. I worry about drilling the holes in the pack and it not working right, but I would be cutting holes in it either way for the straps coming through the pack.
:jet pack What should I do?

 

LionsPride

Active Hunter

• Feb 23, 2006

• #2

realisitcally your gonna want to wait until you have your hard armor done and jet pack harness made, if you don't already. Have a friend hold up the jet pack while your wearing the custume, position it where you want the jet pack, then mark where your harness clips come out of your backplate, that will determine where you will want to cut the "coin" slots in your jet pack. More then likely it will fall somewhere like here in the hatch cover of the jet pack:

kudo's to Seeker for the great pic

hope that helps

 

Last edited by a moderator: Jul 24, 2017

M

mlcallanta

Active Hunter

• Feb 23, 2006

• #3

Just a reminder: Cut the slots above the rear JP door.....not on the door itself

Seriously, LionsPride is correct - you have to have your rear armor & body harness installed before you do any cutting. Plan it out first before the actual cutting.

Mardon (MLC)
mlcallanta@yahoo.com

 

Last edited by a moderator: Jul 24, 2017

LionsPride

Active Hunter

• Feb 23, 2006

• #4

Hey while we're at it, does any one have a pic of what they did for attaching the bottom "Divers belt", I have an idea of how i'll probably do mine, but was wondering how everyone else was doing theirs. More coin slots ???

Ive searched the forum and have read countless JP harness threads, but no one has ever said how they hooked it that i've seen.

 

Last edited by a moderator: Jul 24, 2017

Satxer

Active Hunter

• Feb 24, 2006

• #5

Yeah I have all the harness stuff done, I just meant for the end that's on the pack.

I saw a thread for the divers belts in the for sale area.

 

Last edited by a moderator: Jul 24, 2017

stormtrooperguy

Sr Hunter

• Feb 24, 2006

• #6

LionsPride said:

Ive searched the forum and have read countless JP harness threads, but no one has ever said how they hooked it that i've seen.

Click to expand...

i just riveted the belt to the pack. nothing fancy, since no-one ever sees where it's attached.

my backplate has a notch in the bottom center, so i just lined the belt up with that and put a couple of pop rivets in with washers on the inside of the pack to keep them from pulling through.

 

Last edited by a moderator: Jul 24, 2017

LionsPride

Active Hunter

• Feb 24, 2006

• #7

Not a bad idea 7602

Here kinda what I was thinking on doing.....

I just threw this together quick like as a visual, nothing is attached, infact these are just button snap bridges that I had made for the snaps on my TK suit. The idea is that its a belt loop kinda deal where the strap will pass through. I'll epoxy em down/or rivet and paint em blue to match the pack, attach a full length of strapping and connect to the divers belt in front. realistically you could go with just 1 loop but 2 would deffinatly keep the jet pack in place.

 

Last edited by a moderator: Jul 24, 2017

fettswatcop

Active Hunter

• Feb 24, 2006

• #8

Im curious too...does the belt actually connect to the jp or is the belt(buckle) used more for show? When I attached my jp to the harness, the two straps held the jp in place well. I have yet to troop with it, so I might be wrong with the thought of the belt not connecting. Any help out there?

 

Last edited by a moderator: Jul 24, 2017

LionsPride

Active Hunter

• Feb 24, 2006

• #9

Well, in the movie used suit the Divers belt was actually connected to the lower part of the suba frame that supported the JP.

As far as costuming goes, ive heard it go both ways with some just wearing the belt for looks, and some actually attaching it to the JP to keep it from swaying as your walking and or bending over.

 

Last edited by a moderator: Jul 24, 2017

Satxer

Active Hunter

• Feb 24, 2006

• #10

And, this is my jet pack, just needs a spot or 2 of velcro for anti swaying lol!

 

Last edited by a moderator: Jul 24, 2017

Qman101

Hunter

• Feb 25, 2006

• #11

Satxer said:

And, this is my jet pack, just needs a spot or 2 of velcro for anti swaying lol!

Click to expand...

nice jet pack!

ya, what lionspride said. i heard of it in a couple of threads (in fact, i think it's a sticky) while doing searches.

 

Last edited by a moderator: Jul 24, 2017

Gator Fett

Well-Known Hunter

• Feb 26, 2006

• #12

Check out my posts in this thread:
http://www.thedentedhelmet.com/showthread.php?t=9157

The scuba buckle & belt is just attached to the harness for show, and does not connect to the JP. The JP is connected at the shoulders by two clips, which hold it in place nicley. It sways a little if I walk too fast, (like rushing from back stage at the symphony, to the changing room and back again, because you forgot your blaster! :facepalm ) but as Boba, you are not supose to rush. Every move is calculated and smooth, so when I am in front of the public, the JP dose not move around at all.

Gator

 

Last edited by a moderator: Jul 24, 2017

fettswatcop

Active Hunter

• Feb 26, 2006

• #13

Thanks gator, thats just what I thought.

 

Last edited by a moderator: Jul 24, 2017