Anyone here do physical battle damage to Sintra armor?

Jodo Kast 2749

Active Hunter

• Feb 24, 2004

• #1

I have made a lot of armor but I never bother with making the dents and scrapes. Now that I'm upgrading my personal armor, I want to make the physical damage but don't want to weaken the armor.

I have read that dremmeling the damage in can weaken the plastic so I just want to make some indentations. I was thinking of either heating the area with a heat gun and then pressing a metal rod, screwdriver or something similar in to make the dent or actually heating a metal rod or screwdriver tip and then making the dents with the hot metal. Anyinsights?

 

mobius

Well-Known Hunter

• Feb 24, 2004

• #2

Check out my armor I made all the dents with dremel. I don´t think it has weakend my armor. My armor is 6 mm thick, and unless I would make a deep line accross the armor I don´t thnik it weakens the armor by making few dents with a dremel.

 

B

BountyHunter185

Active Hunter

• Feb 24, 2004

• #3

Ok, what we did is we got our heatgun and applied the heat to the BACK of the armor. The reason you want to put the heat on the back is because when we did it, the heatgun made the sintra all textured. :confused

We basically found anything and everything that looked about like what we wanted the dent to look like and we pressed the object into the sintra until we got the desired look. Be sure the object you are pressing in has some sort of grip or something you can hold onto so that the metal object you are pressing in doesn't burn you. Also, don't press too hard or the object could possibly burn through the sintra. :angry

This link has some other peoples uses and other tips.
If you would like pics of our stuff and how we did it just let us know.

Hope this helps.

 

TBone

Active Hunter

• Feb 24, 2004

• #4

JK - The armor that I have was "physically" damaged. Looks as though it was heated from the back and had sharp pointy objects pressed into it. I took a small file and scratched even more lines into some of the dents. It actually worked pretty good.

 

phantom viper

Active Hunter

• Feb 24, 2004

• #5

I put dents in my sintra armor with the back of the thermomitor i used to keep an eye on the water temp.
<img src=http://200.72.163.179/cdref/tdh/Armor/dent1.jpg>

 

FANGS

Active Hunter

Community Staff

• Feb 25, 2004

• #6

I damaged mine with a dremel. I used the thicker Sintra sort of by accident because the store I bought it from only carried the one size. I had the sanding thingy on my dremel (the round sanding tube that sits snug over the rubber fitting) to bevel the edges of the armour and it slipped and made a most perfect dent with "tails" that were less indented. I like it so I did some more. When I painted I painted the green first, then the silver middles and yellow around the edges....but because of the actual dents you really can't tell that the green is actually the first colour. I was certainly pleased with the results.

 

Jodo Kast 2749

Active Hunter

• Feb 29, 2004

• #7

Well, I did the damage on my new armor last night and really liked the results.

I basically just used my heat gun to heat the back of the sintra then flipped it over and did the dents with the bottom of a wooden spoon and the scrapes with a butter knife.

I tried heating a steel piece to make the damage but it wasn't working nearly as well as heating the sintra itself.

Thanks to everybody for their insights.

 

M

micke

Active Hunter

• Feb 29, 2004

• #8

I used a ciggarette lighter on my styrene armor. I just heated up the armor from underneath and pushed it down from the top with a blunt object and voila!! A dent

 

TBone

Active Hunter

• Mar 1, 2004

• #9

micke wrote:
I used a cigarette lighter on my styrene armor. I just heated up the armor from underneath and pushed it down from the top with a blunt object and voila!! A dent

Click to expand...

That's exatly what I did on my knees...I haven't tried the cod piece yet. Since it is 2 ply, I thought I might melt it too bad with the flame.

 

broodmceto

Hunter

• Apr 2, 2004

• #10

On the three little dents on Boba's lower (stomach) chest armor, I used a bic pen. Just do it when you pull it out of the boiling water. Not too bad.

BTW - Sintra's easier to cut after it's boiled.

 

carbonitekid

Active Hunter

• May 13, 2004

• #11

Does it matter when you put the damage on ie before or after you form it up? Upgrading from my old sheet metal armor to sintra (material for all chest pieces cost me £5:00 /$9:00(?) )

 

Jodo Kast 2749

Active Hunter

• May 13, 2004

• #12

Not really. Just beware that the pressur eof making the damage "might" throw off the overall form.

 

carbonitekid

Active Hunter

• May 13, 2004

• #13

Thanks. I will keep that in mind.

 

Muad Dib

Active Hunter

• Jul 3, 2004

• #14

To make the dents in mine, I heated up the BACK of the armor in the correct spot with a lighter and then pressed a small rock into the front until I liked how it looked. I don't have a digital camera ( I am pathetic) so I can't post pics but it came out perfect.

 

FettTheHunter

Active Hunter

• Jul 10, 2004

• #15

I made my armour ( I've only made the cod piece so far )look damaged by shoot it a lot with a little soft air gun

It looks sort of alright but I might have to remake it

 

L

LisaFett

Active Hunter

• Jul 10, 2004

• #16

I carved damage in using all the nifty dremel attachments available.

 

C

Chrima

Active Hunter

• Jul 14, 2004

• #17

Here is another nifty trick.

For Vacced armor or sintra this should work.

On the back of the armor, locate where you want the dent. Then apply Hot glue to the area. Keep swirling it around with the tip of the glue gun to keep the glue melted.

Then from the front use an appropriately sized blunt object and push in to make the dent. Then run cold water over it, or have a wet cloth handy to cool it down. The heated plastic will tend to spring back. Cooling it off helps hold its shape.

Then when the hot glue is dry, you should just be able to pop it off.

I use to dremel my holes out, but just started using this technique. Works much better, in my opinion. When dremeling, the plastic tends to melt and also you have to finish up with sanding.

Anyway, this is a similar method to some of the others, but I think a bit easier to localize the heating.

Later,

Chris

 

phantom viper

Active Hunter

• Jul 14, 2004

• #18

That is a great idea. I will have to try it. Thanks for sharing.